Atlantic Ultraviolet SANITAIRE RS140 Посібник користувача - Сторінка 3
Переглянути онлайн або завантажити pdf Посібник користувача для Аксесуари Atlantic Ultraviolet SANITAIRE RS140. Atlantic Ultraviolet SANITAIRE RS140 16 сторінок. Ultraviolet room air sanitizers
Друкувати сторінкуSAFETY WARNINGS
•
All personnel should be alerted to the potential hazards indicated by the product safety labeling on this unit.
•
The following conventions are used to indicate and classify precautions in this manual and on product safety labeling. Failure to
observe precautions could result in injury to people or damage to property.
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
Danger indicates an IMMINENTLY
hazardous situation, which, if not avoided,
WILL result in death or serious injury.
Caution indicates a POTENTIALLY
hazardous situation, which, if not avoided,
MAY result in minor or moderate injury.
This symbol/pictorial is used to identify an ELECTRICAL
SHOCK or ELECTROCUTION hazard
This symbol/pictorial is used to identify the need to
wear approved ultraviolet blocking eye wear.
This symbol/pictorial is used to identify the need to
wear protective gloves.
SAFETY INSTRUCTIONS
To guard against injury, basic safety precautions should be observed, including the following:
1. Read and follow ALL safety instructions.
rays are harmful to the eyes and skin.
2.
Intended for indoor use only.
3. Do not alter design or construction.
4. Do not use this fixture for other than its intended purpose, as described in this manual.
5.
Do not override safety interlock.
6. Do not mount under any source of moisture or condensation, such as humidifiers, cooling coils, etc.
7.
Do not remove any labels or devices.
8.
Do not operate without proper electrical ground.
9. Do not operate the unit if there is visible or suspected damage to the unit or, if applicable, there is damage
AS OF MAY 2002 THESE LABELS ARE BEING USED ON ALL OUR PRODUCTS
to power cord and/or plug.
AIR
10. Keep inlet and outlet, of the blowers, clean and clear of debris.
Part No. 00-0198A1 (1.25 x 3)
11.
Do not operate without access cover secured.
WARNING
12. Stay clear of blowers, or other moving parts that can cause injuries.
This fixture is designed for use with germicidal
ultraviolet lamps and must be installed in
13. Utility power supplied, to the unit, MUST match power requirements listed on the unit label.
compliance with competent technical directions
so that the users eyes and bare skin will not be
subjected to injurious radiation.
Always disconnect power to the unit before performing any service or maintenance.
14.
No. 00-0198A1
15. Read and follow all notices and warnings on the unit.
16. SAVE THESE INSTRUCTIONS.
SAFETY LABELS
AIR & WATER
2.75 x 1.5)
Part No. 00-0195A2 (
WARNING
ULTRAVIOLET
RADIATION
U U V V
Protect eyes and skin
from direct and reflected
radiation.
No. 00-0195A2
Danger Label: Ultraviolet Radiation
2.5 x 2.25)
Part No. 00-0196A1 (
(00-0195A2)
DANGER
HAZARDOUS
.
Avoid exposure to direct or reflected germicidal ultraviolet rays. Germicidal ultraviolet
2.75 x 1.5)
Part No. 00-0197A2 (
DANGER
HAZARDOUS
VOLTAGE
Turn off and disconnect
power before servicing.
No. 00-0197A2
Danger Label: Hazardous Voltage
(00-0197A2)
Warning indicates a POTENTIALLY
hazardous situation, which, if not avoided,
COULD result in death or serious injury.
Caution used without the safety alert symbol
indicates a potentially hazardous situation, which,
if not avoided, may result in property damage.
This symbol/pictorial is used to identify an
ULTRAVIOLET LIGHT hazard.
This symbol/pictorial is used to identify the need to wear
approved ultraviolet blocking face shield.
This symbol/pictorial is used to identify components
which must not be disposed of in trash
CAUTION
It is the user's responsibility to determine and validate
the suitability of this equipment for use in the user's
system or process.
No warranty or representation is made by the manufacturer
with respect to suitability or performance of this equipment
or to the results that may be expected from its use.
The user should periodically inspect, clean as necessary
and confirm the presence and good legibility of the product
safety labels. Contact the factory for replacement labels in
the event that any of the labels are missing or illegible.
3