Bosch 4 V-LI Оригінальна інструкція з експлуатації - Сторінка 10
Переглянути онлайн або завантажити pdf Оригінальна інструкція з експлуатації для Пилосос Bosch 4 V-LI. Bosch 4 V-LI 14 сторінок. Professional
Також для Bosch 4 V-LI: Інструкція з експлуатації (31 сторінок), Оригінальна інструкція з експлуатації (7 сторінок), Оригінальна інструкція з експлуатації (10 сторінок), Оригінальна інструкція з експлуатації (7 сторінок), Оригінальна інструкція з експлуатації (48 сторінок), Оригінальна інструкція з експлуатації (15 сторінок)
Друкувати сторінку
OBJ_BUCH-1257-004.book Page 18 Monday, October 21, 2013 10:36 AM
18 | English
Contact Protector
The contact protector 14 attached to the casing prevents ac-
cidental touching of the saw blade during the working proce-
dure and may not be removed.
Plunge Cutting (see figure I)
Plunge cuts may only be applied to soft materials, such
as wood, gypsum plaster boards, etc.!
Use only short saw blades for plunge cutting. Plunge cutting is
possible only with the mitre angle set at 0°.
Place the machine with the front edge of the base plate 7 on
to the workpiece without the saw blade 11 touching the work-
piece and switch on. For machines with stroke rate control,
select the maximum stroke rate. Firmly hold the machine
against the workpiece and by tilting the machine, slowly
plunge the saw blade into the workpiece.
When the base plate 7 fully lays on the workpiece, continue
sawing along the desired cutting line.
Parallel Guide with Circle Cutter (Accessory)
Parallel Cuts (see figure J): Loosen the locking screw 25 and
slide the scale of the parallel guide through the lead 10 in the
base plate. Set the desired cutting width as the scale value
on the inside edge of the base plate. Tighten the locking
screw 25.
Circular Cuts (see figure K): Set the locking screw 25 to the
other side of the parallel guide. Slide the scale of the parallel
guide through the lead 10 in the base plate. Drill a hole in
the workpiece centred in the section to be sawn. Insert the
centring tip 27 through the inside opening of the parallel
guide and into the drilled hole. Set the radius as the scale
value on the inside edge of the base plate. Tighten the lock-
ing screw 25.
Coolant/Lubricant
When sawing metal, coolant/lubricant should be applied
alongside cutting line because of the material heating up.
Maintenance and Service
Maintenance and Cleaning
Before any work on the machine itself (e.g. mainte-
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
the On/Off switch.
For safe and proper working, always keep the machine
and ventilation slots clean.
Clean the saw blade holder regularly. For this, remove the saw
blade from the machine and lightly tap out the machine on a
level surface.
Heavy contamination of the machine can lead to malfunctions.
Therefore, do not saw materials that produce a lot of dust from
below or overhead.
Lubricate the guide roller 9 occasionally with a drop of oil.
Check the guide roller 9 regularly. If worn, it must be replaced
through an authorised Bosch after-sales service agent.
The plastic guide plate 6 should be replaced when worn.
1 609 92A 0C6 | (21.10.13)
After-sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
concerning our products and their accessories.
In all correspondence and spare parts order, please always
include the 10-digit article number given on the type plate of
the machine.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
Tel. Service: (0844) 7360109
Fax: (0844) 7360146
E-Mail: [email protected]
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: (01300) 307044
Fax: (01300) 307045
Inside New Zealand:
Phone: (0800) 543353
Fax: (0800) 428570
Outside AU and NZ:
Phone: +61 3 95415555
www.bosch.com.au
Republic of South Africa
Customer service
Hotline: (011) 6519600
Gauteng – BSC Service Centre
35 Roper Street, New Centre
Johannesburg
Tel.: (011) 4939375
Fax: (011) 4930126
E-Mail: [email protected]
Bosch Power Tools