OBJ_BUCH-1994-001.book Page 15 Tuesday, October 1, 2013 2:18 PM
Technical Data
Cordless Jigsaw
Article number
Rated voltage
Stroke rate at no load n
0
Stroke
Cutting capacity, max.
– in wood
– in aluminium
– in non-alloy steel
Bevel cuts (left/right), max.
Weight according to
EPTA-Procedure 01/2003
* dependent of the battery pack being used
Battery
Permitted ambient
temperature
– when charging
– during operation*
– during storage
Recommended batteries
* Limited performance at temperatures <0 °C
Noise/Vibration Information
Measured sound values determined accord-
ing to EN 60745.
Typically the A-weighted noise levels of the
product are
Sound pressure level
Sound power level
Uncertainty K
Wear hearing protection!
Vibration total values a
(triax vector sum)
h
and uncertainty K determined according to
EN 60745:Cutting board:
a
h
K
Cutting sheet metal:
a
h
K
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
Bosch Power Tools
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
GST 10,8 V-LI
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
3 601 EA1 0..
period.
V=
10.8
Identify additional safety measures to protect the operator
-1
min
1500 –2800
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
mm
18
terns.
mm
70
Declaration of Conformity
mm
3
We declare under our sole responsibility that the product de-
mm
3
scribed under "Technical Data" is in conformity with the fol-
°
45
lowing standards or standardisation documents: EN 60745
according to the provisions of the directives 2009/125/EC
kg
1.5*
(Regulation 1194/2012), 2011/65/EU, 2004/108/EC,
2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Henk Becker
Executive Vice President
°C
0...+45
Engineering
°C
–20...+50
°C
–20...+60
GBA 10,8V x,xAh O–.
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Leinfelden, 23.08.2013
GST 10,8 V-LI
Assembly
Before any work on the machine itself (e.g. mainte-
dB(A)
77
dB(A)
88
dB
3
Battery Charging
Use only the battery chargers listed on the accessories
2
m/s
5.5
Note: The battery is supplied partially charged. To ensure full
2
m/s
1.5
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
2
m/s
5.0
The lithium ion battery can be charged at any time without re-
2
m/s
1.5
ducing its service life. Interrupting the charging procedure
does not damage the battery.
The lithium ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
Observe the notes for disposal.
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
the On/Off switch.
page. Only these battery chargers are matched to the lith-
ium ion battery of your power tool.
English | 15
1 619 P11 351 | (1.10.13)
Друкувати сторінку