Atlas FAP62T Посібник - Сторінка 2

Переглянути онлайн або завантажити pdf Посібник для Спікери Atlas FAP62T. Atlas FAP62T 5 сторінок. Strategyseries ii
Також для Atlas FAP62T: Брошура (5 сторінок), Технічні характеристики (4 сторінок), Інструкція з монтажу (1 сторінок)

Друкувати сторінку

Mounting Accessories

Mounting is simplified with Strategy Series

allow easy installation into drop tile or drywall ceilings with provided tile

mounting rails and a C-Ring assembly. The C-Ring can be attached to the

rails with the screws provided to extend support to the T-bar grid in sus-

pended ceiling applications. Multiple hole locations are provided to allow

the C-Ring to be positioned to the outer edge of the tile if necessary.

For existing dry-wall applications the tile bridge C-Ring and support rails

can be inserted into the hole cut for the FAP62T. For easy positioning

easy maneuvering and location when working "blindly" above the deck.

A uniquely designed "easy access" input panel on the side of the enclo-

sure allows for "thru" conduit runs using flexible or rigid conduit. Below

this cover resides a detachable Phoenix / Euro style locking four-pole

connector, which provides for easy daisy chain wiring to other full range

includes an attractive press-fit grille, which nicely matches contemporary

architecture.

For new construction drywall ceiling applications, the optional FAP62-TR

trim ring is available. This unit provides a marked location for drywall

installers to cut around essentially reserving the desired location in the

ceiling until final installation of FAP62T. Mounting holes are provided to

accommodate 16" or 24" OC stud / joist mounting.

A support ring is also provided on the top of the FAP62T enclosure to

facilitate an auxiliary support cable.

NOTE: IT IS MANDATORY THAT THIS SECONDARY SUPPORT

BE UTILIZED IN DROP CEILINGS FOR SAFETY AND SEISMIC

CONSIDERATIONS.

1601 JACK MCKAY BLVD. ENNIS, TEXAS 75119 U.S.A.

TELEPHONE: (800) 876-3333

FAX (800) 765-3435

C-Ring / V-Rails

FAP62-TR

Architect & Engineer Speciﬁcations

The loudspeaker system shall be Atlas Sound FAP62T. System shall

include a high performance 6" coaxial loudspeaker, ported bass reflex

enclosure and press-fit grille for conventional ceiling installation.

Frequency response for the system shall be 63Hz – 20kHz (±7dB).

Sensitivity shall be 88dB average.

shall be constructed of polypropylene with a butyl rubber surround. The

19 mm tweeter shall be constructed of PEI. Magnet shall be a minimum

of 10 oz (264 g) and the voice coil diameter shall be 1" (25 mm).

Transformer shall be a 70.7V / 100V type with 2, 4, 8, 16, and 32 watt

primary taps (@70.7V) with a front mounted tap selector switch to include

transformer bypass setting for 8Ω direct coupled operation.

Enclosure shall be a deep drawn steel enclosure design. Internal volume

shall be 475 in

. To facilitate connection in conduit systems, enclosure

shall be equipped with an access panel covering a recessed terminal cup.

This cover shall provide a combination

(25mm inside diameter) knock-out on the side access and a top access

compression fitting / strain relief to facilitate flexible conduit up to 22mm

outside diameter or 1" (25mm inside diameter) conduit when the com-

pression fitting is removed.

External wiring shall be accomplished via a removable lockable wir-

ing connector with screw-down terminals to provide both secure wire

termination and pre-wiring capability before loudspeaker installation. The

4 pole locking connector shall facilitate in/out connections and shall be

located in the recessed area behind the conduit access panel.

Seismic support eye shall be provided on top of enclosure for additional

suspension point when used in drop tile ceilings. Construction of enclo-

sure shall be a minimum of 18-gauge deep drawn galvanized metal.

The system shall include a support backing plate to reinforce the ceil-

ing material and tile support rails for use on either 2' x 4' (609mm x

1219mm) or 2' x 2' (609mm x 609mm) suspended ceiling tiles. This

assembly can all be installed from beneath the ceiling tile.

Overall front face diameter shall not exceed 12

from the bottom of the ceiling shall not exceed 8.48" (215mm).

Grilles shall be press-fit, manufactured from 24-gauge perforated steel

mesh and finished in white epoxy. Round grill shall be 10.48" (266mm)

diameter.

The loudspeaker shall be the Atlas Sound FAP62T.

AtlasSound.com

⁄

" (19mm inside diameter) / 1"

⁄

" (318mm); overall depth

2/4