Dromex DHFFM Посібник із швидкого старту

Переглянути онлайн або завантажити pdf Посібник із швидкого старту для Респіраторний продукт Dromex DHFFM. Dromex DHFFM 2 сторінки. Full face mask respirator

Друкувати сторінку

FULL FACE MASK RESPIRATOR

DH FFM

DHFFM

Description

The Dromex® DHFFM full face mask provides the user with unparalleled

vision, comfort and reliability protecting against hazardous vapours, gases

and particulates, provided there is suﬃcient oxygen present in the

contaminated atmosphere.

The Dromex® full face mask utilizes the Dromex® twin uni-ﬁt cartridges and

pre-ﬁlters only.

Special Instructions

All respiratory selections should be read in conjunction with BS EN 529:2005

"Respiratory Protective devices – Recommendations for selection, use, care and

maintenance".

Do not use these respirators or enter in area where:

• The oxygen concentration is not known or is less than 19.5%.

• Contaminants or their concentrations are unknown or are known to be

immediately dangerous to life or health.

• Particulate concentrations exceed levels ﬁxed by the applicable health

and safety regulations or protection factor 40 NPF whichever is lower.

• Gases and/or vapours are present except for respirators designated as

protecting against vapours, in which case vapour concentrations should

not exceed 20 NPF.

• The requirement for leak tightness is unlikely to be achieved if worn

against a beard or facial stubble.

• Do not wear standard eye glasses with a full-face respirator

• Not to be used for ﬁreﬁghting.

• These respirators do not supply oxygen. Do NOT use in oxygen deﬁcient

atmospheres (e.g. tanks or other poorly ventilated areas).

• Do not use in explosive atmospheres.

• Do not modify or alter this device.

Compliance & Conformity

NRCS Homologated to SANS 50136:1998 CL1 as required by the Occupational

Health and Safety Act, 1993 (Act No. 85 of 1993)

EN136:2008 approved: Respiratory protective devices full face masks —

Requirements, testing, marking quality system as per ISO9001:2008.

Speciﬁcations

Type:

Class1 full face masks for light duty use

Material:

Thermo Plastic Elastomer/Rubber

Colour:

Black

Harness:

5-point comfort harness with 2 grip holes for easier ﬁtting

on and removing with gloves and accommodation of

women's hair (ability to wear a pony tail).

Withstands a pull of up to 15KG or 150N

Visor:

Polycarbonate anti-fog and impact resistant with

peripheral optical vision of 220 degree's (110 on the left

and right). The natural ﬁeld of vision is greater than

the 70% speciﬁed of EN136:2008 standards.

One size mask body: Accommodates small to large facial size's

Temperature:

Designed to withstand temperatures of up to 70 ± 3˚

Light weight dual ﬁlter cartridge system evenly

distributes weight of mask and cartridges on the face.

Packaging, Storage & Obsolescence

DHFFM - Packed individually sealed in cardboard box,10 masks per

carton for shipping.

When not in use, store the full-face mask with ﬁlters in the Dromex®

full face mask storage bag that can be worn on the operator's waist.

Store in a cool dry place, away from direct sunlight at temperature

between-20˚C and + 40˚C and where relative humidity is less than

75% and away from sources of possible contamination and physical

damage.

+40˚C

DHFFM

<75%

-20˚C

Cleaning & Maintenance

- Remove cartridge ﬁlters from connectors and all inhalation and

exhalations valves.

- Clean / disinfect the face piece and components with a damp cloth,

using lukewarm with all-purpose detergent

(neutral, pH 6-8, e.g.: washing-up liquid), warm soapy water or cleaning

solution not exceeding 30 degrees.

- Do not immerse the product in water or use abrasive cleaners.

- Do not use solvents (e.g alcohol, acetone, turpentine), hot water, strong

detergents, bleaches or petroleum based products to clean any part of

masks.

- Dry in air at room temperature.

- Replace all components after cleaning and inspect for visible damage.

Shelf life

5 years, with correct maintenance and storage procedures. Discard

immediately if mask is damaged and tears are visible.

Materials

None of the materials used in the manufacture are known to adversely

aﬀect the hygiene or health.

Disposal

All industrial waste should be disposed of correctly according to local

regulations and good disposal practice. Respiratory protective

devices should be disposed of considering the hazardous substance

they were used for. Please consider recycling.

Dromex: Unit 1, 1 Blase Road, New Germany, 3620, South Africa

T. +27(31) 713 1960 E. [email protected]