anko LD-K1035 Посібник користувача - Сторінка 3
Переглянути онлайн або завантажити pdf Посібник користувача для Чайник. anko LD-K1035. anko LD-K1035 7 сторінок.
Unpacking
CAUTION! DANGER to children- danger to life due to suffocation/swallowing.
Keep all packing material and plastic bags out of reach of children. Dispose of it immediately.
* Carefully remove all parts from the packaging and check that no parts are missing or damaged during
shipping. If the product is damaged, do not use. Please return it to Kmart for replacement.
* Remove all packaging material.
First time use
IMPORTANT! during the below process DO NOT fill the kettle more than the min (0.5L) mark on the kettle.
Filling above the min. mark will cause over boil and spillage out of the spout.
To ensure a long service life of the water kettle and to remove any residue from manufacturing process,
proceed as follows before using it for the first time:
1. Fill the kettle with water and add vinegar in a ratio of 1:3 (1part vinegar / 3 parts water).
2. Bring to a boil (see Boiling water), then pour away.
3. Allow the kettle to cool down and then refill it fresh water, boil the water and then pour it away again
To avoid scale deposits, descale the water kettle at regular intervals (after about every 15th use)
as described in the section "Descaling".
The appliance can heat water to 80℃, 85℃, 90℃, 95℃, 100℃ (boil) and keep warm function (Note: keep
warm function cannot be use when 100℃ boiling function is selected). When the appliance is plugged in, all
lights will be on for 5 minutes, the appliance is in standby status. All the lights will switch OFF, if the
appliance is not used after 5 minutes. If you touch any of the buttons, all the lights will switch back ON again
to indicate standby status.
1. Heat water
a. Press the button for 80℃ in standby status, and the corresponding LED light will flash to indicate the water
is heating up. The appliance will start to heat the water till it reaches the selected temperature. The LED
light will stop blinking and remain steady ON when the water in the kettle has reached the selected
temperature. The LED indicator light will turn OFF automatically after five minutes.
b. The same working procedure applies to 85℃, 90℃, 95℃ and 100℃ function.
2. Heat water and keep warm
c. Press the button for 80℃ first, then press the keep warm button. The LED light for 80℃will flash while the
keep warm button will be illuminated. The LED light will stop blinking and remain steady ON when the
water in the kettle has reached the selected temperature. The appliance will stay in keep warm status for 30
minutes.
NOTE: during keep warm function the kettle will switch ON & OFF to maintain the selected water
temperature, this is normal.
d. The same working procedure applies to 85℃+ keep warm, 90℃ + keep warm, 95℃ + keep warm.
NOTE: The keep warm function cannot be selected when boiling water at 100℃.
Boiling water
WARNING! risk of fire and burns:
* The kettle body and its lid become hot while in use. Do not touch them.
* The lid must be tightly closed during the boiling process. It must not be opened while pouring water out.
Let the appliance cool down before opening the lid.
CAUTION! – boiling water can cause damage to property and cause injuries.
* Do not fill the water container with less than (0.5L) or more than (1.7L) of water.
IMPORTANT! this appliance is not intended to heat liquid other than water
1. Press the lid release trigger. The lid will open automatically.
2. Fill the kettle with the amount of water required. You can check the water fill level on the water indicator
on the kettle.
--How to use your kettle --