Annovi Reverberi AR 60 LFP Інструкція з монтажу Посібник з монтажу - Сторінка 19
Переглянути онлайн або завантажити pdf Інструкція з монтажу Посібник з монтажу для Водяний насос Annovi Reverberi AR 60 LFP. Annovi Reverberi AR 60 LFP 19 сторінок.
Друкувати сторінку
A.R. NORTH AMERICA
Use of engine :
31185:
B&S Vanguard 6.5
Kohler SH265 - CH270
Subaru E17 - 21
Honda GP160 - GX160
Ø 3/4" Straight Keyed Shaft
Pos
Cod.
Description
1 3120360 Gasket
2 3120340 Flange
3
620960 Body
4 3120350 Shaft
5
780230 Washer
6
880280 Bolt
TCEI M6x18
7
651620 Gear
Z=64
8
620470 Screw
TCEI M10x20
9
620950 Gasket
10 1140370 Plug
11 1980740 Plug
3/8" G ottone
12
740290 O-ring
Ø 14x1,78
13
651000 Bolt
TCEI 5/16" 24 UNF 1"
14
540300 Bolt
TCEI M10x30
15
620990 Bearing
16
621660 Pinion
Z=11
17
320240 Ring
seeger Øe 40
18
961780 Bearing
19
881090 Key
20
961790 Ring
seeger Øi 68
21
961800 Ring
tenuta
22 3120350 Key
180030 Screw
23
TCEI M8x20
24 1380630 Key
di manovra
25
200231 Washer
Suggested Oil
For gas engine with Ø3/4" shaft, flange SAE J609a
*Torque: in/lbs +/- 10%
2018 AR North America
AR 31185 : Gear Reduction
2
14
I
23
10
11
12
14
I
3
12
11
21
19
20
1.Lubricate the gasket (Ref. 1) on the pump adapter flange (Ref. 2). Slip the flange
Note
Q.ty
over the machined surface of the casting, shaft end of pump. Install (4) mounting
1
bolts (Ref. 14) through the adapter flange into the pump body.
1
1
2. Install the shaft hub (Ref. 4) on the pump shaft, after inserting the key (Ref. 22).
Secure the hub by threading the retaining bolt (Ref. 6) through the retaining
1 AR45bp-AR80bp
washer (Ref. 5) into the pump shaft.
1
1
T90*
3.Install the pump gear (Ref. 7) with the pilot diameter of the gear inserted into
1
the inner diameter of the pump shaft. Secure firmly onto the shaft using M10 x
3
T180*
25 socket head cap screws (Ref. 8) and lock washers (Ref. 25).
1
1
4.Align the holes in the pump adapter flange (Ref. 2) with threaded holes in the
3 T180*
gearbox body. Lubricate the gasket (Ref.9) and place it in position on the
3
gearbox body (Ref. 3). Install the gearbox body (Ref. 3) on the pump adapter
4 Geomet T220*
flange (Ref. 2) and secure firmly with M10 x 75 socket head cap screws (Ref. 14).
8
T220*
Install the M8 x 20 socket head cap screw (Ref. 23) and tighten securely.
1
5.Insert the long key (Ref. 19) into the engine shaft keyway. Apply anti-seize to
1
the motor shaft. Align the keyway in the gear reducer input shaft (Ref. 16) and
2
slide the pump and gear reducer onto the engine shaft.
1
1
6.Align the holes in the gearbox body with threaded holes in engine boss. Insert
1
5/16"x1"-24 socket head cap screws through the gearbox body (Ref. 3) and
1
thread them into the threaded holes in the engine boss. Securely tighten with
1 AR45bp-AR80bp
the hex wrench provided.
1 T220*
1
7.The vent plug (Ref. 10) must always be installed in the uppermost threaded
hole of the gearbox body (Ref. 3).
3
Type
8.Fill the gear case with 90W gear lube. To properly fill, first tighten the bottom
plug (Ref. 11); then remove one side plug (Ref. 11) and the vent plug (Ref. 10). Fill
90 W Gear Lube
until the gear lube is no higher than the mark on the dipstick.
9.Replace and tighten the side plug and the vent plug.
22
1
6
9
5
4
8
25
7
24
12
11
13
15
16
17
18
17
93 - 1
93