Daintree GE current Tetra GEPS24-100U-GLX Посібник з монтажу - Сторінка 3

Переглянути онлайн або завантажити pdf Посібник з монтажу для Джерело живлення Daintree GE current Tetra GEPS24-100U-GLX. Daintree GE current Tetra GEPS24-100U-GLX 3 сторінки. Led systems power supply 120-277 vac input/24vdc output/100w

Друкувати сторінку

Tetra

Power Supply GEPS24-100U-GLX

Power Supply Specifications

Performance Data

Input Voltage (VAC)

Input Frequency (Hz)

Input Current (A)

THD

Output Voltage (VDC)

Output Current (ADC)

Output Power (W)

Environmental Operating Temperature Range

Environmental Humidity (non-condensing)

Environmental Storage Temperature Range

Environmental Rating

Dimensions

Troubleshooting

Symptom

Solution

All LEDs are OFF

• The GEPS24-100UGLX features a new built in output overload shutdown feature that automatically resets when the AC supply

is removed and reapplied. So if all letters are off, first verify whether or not the output can be reset by first switching off then

switching back on the AC supply. If the letters do not re-light, then proceed to the following solutions.

• Check AC input connection and/or check circuit breaker.

• Check wire connection(s) at the Tetra® LED System and power supply for improper termination(s) or short circuits. Properly

terminate or replace the wire connection(s).

• Check that connections are the red striped wire (+) of the LED strip to the red wire (+) of the power supply and the white wire (-)

of the LED strip to the black or blue wire (-) of the power supply.

• Ensure the overall length of the Tetra® LED System does not exceed the maximum load. If so, remove the excess load and cycle

the AC supply to reset the drivers built in overload protection.

Some LEDs

• Ensure the length of supply wire is equal to or below the recommended remote mounting distance.

appear dim

Some of the

• Check wire connection(s) at the Tetra® LED System and power supply for improper termination(s) or short circuits. Properly

LEDs are

terminate or replace the wire connection(s).

not illuminated

• Check that connections are the red striped wire (+) of the LED strip to the red wire (+) of the power supply and the white wire (-)

of the LED strip to the black or blue wire (-) of the power supply.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to

cause harmful interference in which case the user will be required to correct the interference at his own expense.

This Class [A] RFLD complies with the Canadian standard ICES-005. Ce DEFR de la classe [A] est conforme à la NMB-005 du Canada.

This product is intended to be used as a lamp control gear that is installed after the mains control switch.

Min

108

–

0.35

–

0.9

24.0

–

-40°C

IP66 rated: must be protected from direct exposure to the weather

9.5 in. x 1.7 in. x 1.1 in. (241 mm x 43.2 mm x 28 mm)

Conforms to the following standards:

www.gecurrent.com

General Electric Company and are used under license. Information provided is subject to change without

notice. All values are design or typical values when measured under laboratory conditions.

SIGN244 (Rev 02/08/21) Enovia - A-1020632

Installation Guide

Typical

Max

120-277

50/60

–

24.5

–

+25°C

+60°C*

–

+85°C

*Maximum case temperature is 85°C

305

–

1.1

–

25.2

4.0

95%