DSC Impassa WT4989 Інструкція з експлуатації
Переглянути онлайн або завантажити pdf Інструкція з експлуатації для Система безпеки DSC Impassa WT4989. DSC Impassa WT4989 2 сторінки. Two-way wireless key
Також для DSC Impassa WT4989: Інструкція з експлуатації Посібник з експлуатації (8 сторінок), Інструкція з експлуатації (2 сторінок)
Друкувати сторінку
Operating Instructions
IMPORTANT: This equipment shall be used in an environment that provides
the pollution degree max. 2 in NON-HAZARDOUS locations ONLY.
The WT4989 is a five-button two-way wire-
less key with an LCD icon display and a
built-in buzzer. The LCD provides display
icons that come on to show the system sta-
tus when the Status Request button is
pressed. In addition, the buzzer will "beep"
to audibly indicate a button was pressed, or
that the wireless key has sent a command to
the control panel. The wireless key commu-
nicates with compatible wireless receivers
(i.e., 9155 security systems) to allow you to
arm, disarm and confirm your requested actions, as well as other keypad functions
with the convenience of wireless portability. Together with your installer, you can
decide which functions you wish to have accessible from your portable key. To acti-
vate, press and hold a button for approximately 1 second*. Note that some key
functions require a 3 second** press. The LCD display backlighting and antenna
icon turn on and the buzzer beeps once, indicating that a button has been pressed.
These actions also confirm that a signal has been sent to the control panel receiver.
Specifications
Operating Frequency: 433 MHz; Wireless Range: (n/a)m (outdoor, line of sight);
Batteries: (2) 3V Lithium (CR2032); Dimensions (LxWxH): 75mm x 40mm x
14mm; Weight: 41g; Water Resistant
The Default Button Functions
Press this button for 1 second to view the control panel
Status Request
system status via the LCD display icons.
Press and hold this button for 3 seconds to lock the keys. The Tri-
Keylock**
angle icon (
) flashes briefly before the keyfob turns off. To unlock the keys,
press this button for 3 seconds.
Press to arm
Stay Arming:
Away Arming:
your system in Stay mode. All
tem. Interior and exterior zones will be
perimeter zones are active but
armed.
interior zones remain inactive.
Panic Alarm**:
central monitoring station of a situation
Press to disarm your
Disarm:
requiring police.
system.
Command Output 1**
Command Output 2**
both at the same time to activate the
Press both at the same time to acti-
assigned output.
vate the assigned output.
Transmit Default Serial
Mode** Press all at the same time to pro-
Number** Press both at the same
gram optional button functions. This should be
done by the installer. the battery icon flashes.
time to send the serial number.
Other WT4989 options are available in order to program the best possible combi-
nation to suit specific needs. For UL Listed installations, refer to the control panel's
Installation Manual for details.
How to Enroll the WT4989
This section describes how to set up and program your remote, this should be
done by the installer. The following outlines the basic steps for programming and
enrolling this device on PowerSeries receivers. For additional options, or for other
receivers, please refer to the specific receiver Installation Manual.
Step 1-Enroll the Device
LCD ICONS
The WT4989 is enrolled by Quick Enrollment or Serial Number Programming.
Quick Enrollment
1. Section [898], enter through installer programming.
2. Press any key on the wireless device to activate it.
3. The Keypad will display the 8-digit ESN, confirm by pressing [*].
4. Repeat from step 2 to enroll additional remotes.
Program Electronic Serial Number (ESN)
1. Section [804], subsections [101]-
[116].
2. Enter the 8-digit ESN located on the
back of the unit.
Step 2-Program Function Buttons
Section [804], subsections [141] - [156]
0 3 Button 1 Stary Arming
0 4 Button 2 Away Arming
2 7 Button 3 Disarm
How to Program the WT4989 Options
Changing the programming will affect operation. This should be done by the installer. To pro-
gram WT4989 Options: (1) Press and hold all 4 buttons at the same time until the
icon comes on and begins to flash. (2) Choose a WT4989 Programmable Option from the
table. These options have toggle features, to return to the default, repeat steps 1 and 2.
Press to arm your sys-
To Program this Option
Remove the Keypress Beeps.
Press to notify your
Remove the 3-Second Delay on (
Turn off the System Disarm (
Press
Turn off the (
) key.
Turn off the (
)key.
Turn off the Backlighting function.
Device Programming
NOTE: Do not press any other button while in Programming mode.
NOTE: For UL Listed installations, the 'Arm/Disarm Bell Squawk' feature of
the control panel must be enabled. The 3-second delay on the Panic key must
not be disabled. The Bell Squawk must be heard from outside the premises.
Arming/Disarming confirmations must be indicated by the keyfob LCD dis-
play. Refer to the control panel's Installation Manual for details.
[101]Key 1
[102]Key 2
3 0 Button 4 Panic
1 3 Buttons (1+2) Command Output 1
1 4 Buttons (3+4) Command Output 2
Do This
Press the (
) key.
) key. Press the (
) key.
) key.
Press the (
) key.
Press the (
) key.
Press the (
) key.
Press the (
)+(
)
keys at the same time.
Control Panel System Status Display
The table below summarizes the possible main system statuses that can be shown
.
by the WT4989 LCD display
ICON (S=Steady, F=Flashing) SYSTEM STATUS
(S) System Trouble
(S) Alarm in Memory
(F) Active Alarm
(S) Disarmed - Ready
(F) *9 Armed - Away
(F) Disarmed - Not Ready
(F) *9 Armed - Stay
(S) Away - Armed
(F) *9 Armed - Night
(S) Stay - Armed
(S/F=Steady or Flashing, icon state will
(S) Night - Armed
depend on the system state)
Keyfob Status
(S/F)Exit Delay-Away Arming
(S) WT4989 Low Battery
(S/F) Exit Delay-Stay Arming
(F) Device Programming
(F) Critical Low Battery
(S/F) Exit Delay-Night Arming
(F) Keylock enable
Replacing the Batteries
Under normal conditions the batteries last 3 years. Dur-
ing each button press the keyfob sends the status of its
battery to the control panel receiver. If the battery is low,
the battery icon on the LCD display comes ON. If the bat-
tery has reached a critically low state the battery icon
flashes. To replace the battery, remove the top cover by
inserting a coin into the slot located on the center bottom
and twist to expose the batteries. Replace both batteries
with lithium 3V batteries (CR-2032), see diagram.
NOTE: The polarity of the battery must be observed, as
shown in the diagram.
REPLACE ONLY WITH THE SAME OR EQUIVALENT
TYPE RECOMMENDED BY THE MANUFACTURER. Keep away from
small children. If batteries are swallowed, promptly see a doctor. Do
not try to recharge these batteries. Disposal of used batteries must
be made in accordance with the waste recovery and recycling regula-
tions in your area
Belt Clip Assembly
Compatibility
The WT4989 is compatible
with the following receivers:
PC9155-433, PC9155D-433
and PC9155G-433
9043