DSC HS2LCDPX Інструкція з монтажу Посібник з монтажу - Сторінка 2
Переглянути онлайн або завантажити pdf Інструкція з монтажу Посібник з монтажу для Клавіатура DSC HS2LCDPX. DSC HS2LCDPX 11 сторінок.
Друкувати сторінку
Introduction
The HS2LED/HS2ICN(P)(RF)x/HS2LCD(RF)(P)x keypads are
compatible with the PowerSeries Neo HS2016/32/64, HS2016-4*
and HS2128 panels. The RF keypads combine a wireless trans-
ceiver with the respective HS2 keypad.
*Model not UL/ULC listed.
Specifications
Temperature range: - 10°C to +55°C (14°F to 131°F);
l
UL/ULC: 0°C to +49°C (32°F to 120°F)
Humidity (MAX): 93%R.H. non-condensing
l
Plastic enclosure protection degree: IP30, IK04
l
Voltage rating: 13.8Vdc nominal (power provided by the com-
l
patible control panel)
Connects to control panel Corbus via 4 wires
l
1 configurable zone input or PGM output*
l
HS2LED/ HS2ICN(P)/HS2LCD(P)/HS2ICNRF(P)
l
/HS2LCDRF(P) Current draw:55mA(min)/105mA(max)
Wall-mount tamper
l
5 programmable function keys
l
Ready (Green LED), Armed (Red LED), Trouble (Yellow
l
LED), AC (Green LED)
Dimensions (L x W x D): 168mm x 122mm x 20 mm
l
Weight: 260g
l
Low temperature sensor
l
Frequency: 433 MHz (HS2ICNRF4/HS2LCDRF4)
l
868 MHz (HS2ICNRF8/HS2LCDRF8)
l
912-919MHz (HS2ICNRF9/HS2LCDRF9)
l
Up to 128 wireless zones
l
Zone not to be programmed as Fire type or 24h type.
NOTE: Keypads contain no serviceable parts.
NOTE: Only models operating in band 912-919MHz are UL/ULC
listed.
Unpack
The keypad package includes the following:
HS2LED/ICN(RF)/LCD(RF) HS2ICN(RF)P/LCD(RF)P
1 keypad
1 keypad
4 mounting screws
4 mounting screws
2 end-of-line resistors
2 end-of-line resistors
Keypad inner door labels
Keypad inner door labels
1 tamper switch
1 tamper switch
Installation Instructions
Installation Instructions
Mini Proximity (prox) tag (MPT)
Table 1: Compatible Devices
Wireless PG smoke detector
Wireless PG smoke and heat detector
Wireless PG CO detector
Wireless PG PIR motion detector
Wireless PG PIR + camera motion
detector
Wireless PG curtain motion detector
Wireless PG dual tech motion detector
Wireless PG mirror motion detector
Wireless PG outdoor motion detector
Wireless PG glass break detector
Wireless PG shock detector
Wireless PG flood detector
Wireless PG temperature detector (indoor) PGx905UL
Outdoor temperature probe (requires
PGx905)
Wireless PG key
Wireless PG key
Wireless PG panic key
Wireless PG 2-button key
Wireless PG indoor siren
Wireless PG outdoor siren
Wireless PG repeater
Wireless PG door/window contact
Wireless PG door/window contact
w/AUX
NOTE: In this chart, x in the model number represents the oper-
ating frequency of the device as follows: 9 (912-919 MHz), 8
(868MHz), 4 (433MHz).
NOTE: Only models operating in the band 912-919 MHz are
UL/ULC or cUL listed where indicated. Only UL approved
devices are to be used with UL/ULC listed systems.
Mount the Keypad
Mount the keypad where it is accessible
from designated points of entry and exit.
Once a dry and secure location has been
selected, perform the following steps to
mount the keypad.
Disassemble Keypad
Insert the tip of a flat-head screwdriver
into the slots at the bottom left and right
of the keypad.
Gently pry open the faceplate. This will
remove it and allow access for mounting.
Mount and Wire Keypad
PGx926UL
PGx916UL
PGx913
PGx904(P)UL
PGx934(P)UL
PGx924UL
PGx984(P)
PGx974(P)UL
PGx994UL
PGx912
PGx935UL
PGx985UL
PGTEMP-PROBE
PGx939UL
PGx929UL
1. Secure keypad to wall using mounting holes. Use all four
PGx938UL
screws provided unless mounting on a single gang box. Use the
PGx949UL
plastic anchors supplied if the unit is to be mounted on drywall.
PGx901UL
2. If using the keypad tamper, secure the tamper plate to the wall
PGx911UL
with a screw.
PGx920UL
NOTE: For UL/ULC listed commercial burglary installations, the
PGx975UL
use of the keypad tamper is mandatory.
PGx945UL
3. Run wire through wiring slot or knockouts. Connect Corbus and
PGM/Zone wiring to keypad. Place tamper switch into tamper
hole on backplate.
4. Place keypad into backplate, ensuring the wire is pushed back
into the wall as much as possible. Route the wire inside the
keypad, ensuring high components are avoided. Snap the front
assembly closed, ensuring that there is no pressure to the keypad
from the wire below.
NOTE: If any tension is found between the front keypad assembly
and the wiring, open the keypad, reroute the wire and close again.
Repeat these steps until the keypad is closed properly.
Wiring
1. Before wiring the unit, ensure that
all power (AC transformer and bat-
tery) is disconnected from the con-
trol panel.
2. Connect the four Corbus wires
from the control panel (red, black,
yellow and green) to the keypad ter-
minals. Refer to the diagram:
If programmed as an input, a device
- such as a door contact - may be
connected to the 'P/Z' terminal of
the keypad. This eliminates the need to run wires back to the