DSC PC1000 Інструкція з експлуатації - Сторінка 6

Переглянути онлайн або завантажити pdf Інструкція з експлуатації для Клавіатура DSC PC1000. DSC PC1000 8 сторінок.
Також для DSC PC1000: Інструкція з експлуатації (8 сторінок)

Друкувати сторінку

DOOR CHIME FEATURE

The door chime feature is used, while the panel is disarmed, to provide a tone from

the keypad each time a door or window is opened or closed. The doors and windows

which will provide this indication are programmed by your installer.

Enter[*] [5], [Master Code],

[OJ

to turn the door chime feature ON and OFF. When

the command is entered, the keypad will beep 3 times if the feature is being enabled

and will sound one beep if the feature is being disabled.

SPECIAL FUNCTION COMMAND

The PC1000 can be programmed at the time of installation to operate other devices

such as electric door strikes, door openers, electric lights, cameras, etc. by pressing

[*] then [7] on the keypad. Your installer will instruct you on the use of this command.

AT-HOME ARMING COMMAND

Entering[*], [9] before the 4 digit arming code arms the panel with no entry delay

on the entry zones, and bypasses the interior zones that have been programmed as

"home-away" zones. This command is used to arm the system if someone is

remaining on the premises.

KEYPAD ZONES

There are three zones which can be activated from the keypad. A fire alarm is

activated by pressing the [1] and [3] keys at the same time. The fire alarm sounds

the bell/siren in a pulsed mode. A transmission will be sent to the monitoring station

ONLY if it has been programmed to do so by the installer.

The PC1000 can be programmed at the time of installation to send a transmission to

the monitoring station by simultaneously pressing keys [4] and [6]. The installer will

provide instructions on its use when required.

The Police (or Panic) alarm is activated by pressing the [*land[#] keys at the same

time. The panic alarm can be programmed to be audible or silent. There is no

annunciation from the keypad. A transmission will be sent to the monitoring station

ONLY if it has been programmed to do so by the installer.

AUTO-TEST TRANSMISSION

The PC 1000 can be programmed at the time of installation to send a test code to the

monitoring station at regular intervals. The frequency and time of the test transmission

is set by the monitoring station and should not be changed without their knowledge.

FIRE LOOP OPERATION

ARMED MODE ("Armed" light ON)

1. On alarm the signal will pulse.

2. Enter access code to silence the signal and also disarm the panel.

3. Press [*l then [7] to reset the smoke detector(s) if the panel has been

programmed to do so; "System" and "Ready" lights will come ON steadily.

DISARMED MODE ("Ready" light ON)

1. On alarm the signal will pulse; zone 4 and "System" lights ON steadily

2. Enter access code to silence signal.

3. Press [*] then [7] to reset the smoke detector(s) if the panel has been

programmed to do so; "System" and "Ready" lights will come ON steadily.

FIRE LOOP TROUBLE

1. Open circuit on the fire loop (zone 4 ); "System" light ON steadily and keypad

sounder beeps.

2. Press [#] to silence the trouble.

3. Press [*]then [2] to view the source of trouble; "System" and zone 3 lights flash

to indicate a trouble on the fire loop (zone 4).

4. Press[#] to exit view-trouble mode; "Ready" and "System" lights will come ON

steadily.

5. When the trouble condition is repaired, the "System" lights will go OFF leaving

only the "Ready" light ON.

TESTING

IT IS RECOMMENDED THAT THE SYSTEM BE TESTED ON A WEEKLY BASIS

NOTE: Perform system tests in the off-peak hours, such as early morning or late

evening.

1. Inform the monitoring station that you are testing your system.

2. Disarm the system ("Ready" light should be ON).

3. Perform a battery/bell test by pressing[*] then [4]. The alarm will sound for

about 2 seconds. If a trouble occurs after the test, press[*], [2] to view the

trouble condition.

4. Activate each sensor in turn (e.g. open a door or window). Observe the zone

light come ON as each sensor is activated. The zone light will go OFF as each

sensor is restored to normal (door or window is closed).

5. Press the [1] and [3] keys at the same time. The signal will sound in a pulsed

mode. Arm then disarm the panel to silence the signal.

Continued... ►