DSC Power 832 Інструкція з експлуатації - Сторінка 7
Переглянути онлайн або завантажити pdf Інструкція з експлуатації для Блок управління DSC Power 832. DSC Power 832 11 сторінок. Central station talk / listen module
Також для DSC Power 832: Інструкція з експлуатації (18 сторінок), Інструкція користувача (2 сторінок), Інструкція з монтажу Посібник з монтажу (12 сторінок), Посібник користувача (20 сторінок), Інструкція з монтажу (2 сторінок), Інструкція з монтажу (2 сторінок), Посібник з монтажу (17 сторінок)
Друкувати сторінку
Programming codes from an LCD Keypad:
Master Code
Press the [ ] key to enter the function list. Scroll (< >) to...
Press [5] or [ ]. The display will read...
Press (*) for
< >
Access Codes
Enter your current Master Code. The display will read...
Enter Master
Access Code
"01P" represents the first access code. Use the arrow (< >) keys to scroll to "40P"
(*) to Edit
< >
and press the [ ] key to indicate that you wish to program the Master Code. The
User Code
01P
display will read...
Enter the new Master Code. The Master Code must be four digits unless otherwise
Enter New Code
indicated by your installer. Enter digits 0 through 9 only. Once the new code is
1234
< >
entered, the keypad will beep 3 times and the display will read...
(*) to Edit
< >
Press [#] to exit the code programming function.
User Code
01P
Be sure to record your new Master Code on the "System Information" page in this booklet. NOTE: We
recommend that the factory default Master Code [1234] not be used.
Additional Access Codes
To erase, add or change a user code, press [ ] to enter the functions list. Use the arrow (< >) keys to
scroll to the following message...
Press [ ]. Display will read...
Press (*) for
< >
Access Codes
Enter Master
Enter the Master Code. Display will read...
Access Code
[*] to Edit
<>
Use the scroll keys (< >) to find the access code – indicated by "01P" to "32P" –
User Code
01P
you wish to add, change or delete. Press the [ ] key to select the code you wish to
alter. The display will read...
To add or change a code, enter the new code. Access codes must be four digits
Enter New Code
1234
< >
unless otherwise indicated by your installer. Enter digits 0 through 9 only. To delete
an access code, enter [ ]. Once the 4 digit code or [ ] has been entered, the
keypad sounder will beep 3 times and the display will read...
The "P" means the code has been programmed. If there is no "P" then that code is
[*] to Edit
<>
User Code
01P
deleted. Press [#] to exit the code programming function. Do not erase the Master code.
Remember to record your new code(s) on the "System Information" page in this booklet.
Access Code Attributes
Additional programmable attributes, such as zone bypassing capability, can be activated or
deactivated for each access code. For more information regarding access code attributes, please
contact your installer.
10
If An Alarm Sounds
Fire Alarm
If your system has been installed with fire detectors and the alarm sounds in a pulsing mode, follow
your emergency evacuation plan immediately (see "Fire Escape Planning" on page 15).
Intrusion Alarm
If an intrusion alarm sounds, indicated by a continuous bell or siren, the alarm may be silenced by
entering your access code. If the alarm was unintentional, call local authorities immediately to avoid an
unnecessary response.
You can determine the source of the alarm by following the instructions in the "Disarming" section (see
page 6). Once the source of the alarm has been corrected, the panel can be restored to its original
Armed state.
Function Keys
Each keypad has five function keys, located to the right of the number pad, which allow easy single-
button activation of the most commonly used features. If these keys have been enabled by your
installer , you can execute their programmed function by pressing and holding the corresponding key
for two seconds.
For information regarding the operation of the function keys, talk to your alarm installer.
Programming Security Codes
Programming codes from an LED Keypad:
The Master Code
To program the Master Code, enter [ ][5][current Master Code][40][new Master Code]. The Master
Code must be four digits unless otherwise indicated by your installer. Enter digits 0 through 9 only.
Press [#] to return to the Ready state.
Be sure to record your new Master Code on the "System Information" page in this booklet. NOTE: We
recommend that the factory default Master Code [1234] not be used.
Additional Codes
Up to 32 additional access codes (01 through 32) may be programmed.
To program a new code:
Enter [ ][5][Master Code][code number 01 to 32][new access code]. The code number is a double digit
from 01 to 32. Access codes must be four digits unless otherwise indicated by your installer. Enter
digits 0 through 9 only. Press [#] to return to the Ready state.
If an access code already exists for the code number you have selected, it will be replaced by the new
code. Be sure to record your new code(s) on the "System Information" page in this book.
To erase a code:
Enter [ ][5][Master Code][code number 01 to 32][ ]. Press [#] to return to the Ready state. Do not
erase the Master code.
Continued on page 10...
7