AirTime ATDDC4 Посібник з встановлення та експлуатації - Сторінка 3

Переглянути онлайн або завантажити pdf Посібник з встановлення та експлуатації для Годинник AirTime ATDDC4. AirTime ATDDC4 8 сторінок. Wireless digital wall clock

Друкувати сторінку

ATDDC4 Series Installation & User's Guide

One Year Limited Warranty

Lathem warrants the hardware products described in this guide against

defects in material and workmanship for a period of one year from date

of original purchase from Lathem or from an authorized Lathem

reseller. The conditions of this warranty and the extent of the

responsibility of Lathem Time Corporation ("Lathem") under this

warranty are listed below.

This warranty will become void when service performed by anyone other than an

approved Lathem warranty service dealer results in damage to the product.

This warranty does not apply to any product which has been subject to abuse,

neglect, or accident, or which has had the serial number altered or removed, or

which has been connected, installed, adjusted, or repaired other than in accordance

with instructions furnished by Lathem.

This warranty does not cover dealer labor cost for removing and reinstalling the

machine for repair, or any expendable parts that are readily replaced due to normal

use.

The sole responsibility of Lathem under this warranty shall be limited to repair of

this product, or replacement thereof, at the sole discretion of Lathem.

If it becomes necessary to send the product or any defective part to Lathem or any

authorized service dealer, the product must be shipped in its original carton or

equivalent, fully insured with shipping charges prepaid. Lathem will not assume any

responsibility for any loss or damage incurred in shipping.

WARRANTY DISCLAIMER AND LIMITATION OF LIABILITY: Except only the limited

express warranty set forth above, the products are sold with no expressed or

implied warranties of any kind, and the implied warranties of merchantability and

fitness for a particular purpose are hereby expressly disclaimed. No warranties are

given with respect to products purchased other than from Lathem or an authorized

Lathem reseller and any such products are purchased "as is, with all faults." In no

event will Lathem be liable for any direct, indirect, special, incidental or

consequential damages arising out of or in connection with the delivery, use or

inability to use, or performance of this product. In the event any limited remedy

given herein shall be deemed to have failed of its essential purpose, Lathem's

maximum liability shall be to refund the purchase price upon return of the product.

Proof of date of purchase from Lathem or an authorized Lathem reseller is required

for warranty service on this product.

This Warranty grants specific legal rights. Additional legal rights, which may vary by

locale, may also apply.

Should any difficulties arise with the performance of this product during warranty,

or with any Lathem authorized service centers, contact Lathem Time

address below:

200 Selig Drive SW

Atlanta, GA 30336

www.lathem.com

Form USG0084

Lathem Inc

Page 12

Introduction

The AirTime ATDDC4 Wireless Digital Display Wall Clock is designed

with a 4-inch red LED display that can be viewed from distances over

100 feet. The optional 6 digit version provides 2 additional 2-inch

digits. The bright red display shows the hour and minutes or as an

option the hour, minutes and seconds; can be configured for a 12 or 24

Hour format; and keep time synchronized to a Lathem ATX series

transceiver's wireless correction signal. The ATDDC4 series Wall Clocks

can be mounted directly to a wall, to a single gang outlet box or, with

optional mounting kits, as double-faced units from the wall or ceiling.

Clock Operation

When the ATDDC4 series Wall Clock is connected to 120vAC (24vAC

optional) power, it displays the firmware version for 3 seconds and

then changes to 12:00 AM. A flashing LED in the lower right indicates

that it is listening to acquire its initial synchronization signal. When a

signal is received the LED will extinguish and the internal clock will be

set. Note: It may take up to several minutes for the clock to initially

synchronize. After initial reception, the LED will only flash when future

sync signals are received. The clock will continuously listen and correct

itself as needed.

Front Panel

Front Panel with optional 6 digit display

at the

ATDDC4 Series Installation & User's Guide