Attwood 911339 Інструкція з монтажу

Переглянути онлайн або завантажити pdf Інструкція з монтажу для Морське освітлення Attwood 911339. Attwood 911339 2 сторінки. Attwood stowaway light base installation instructions

Друкувати сторінку

Stowaway Light Base

911339 (2-Wire)

911639 (3-Wire)

Installation Instructions

Attwood marine hardware, navigational lighting, bilge pumps, and

other marine accessories are specified more than any other brand

by America's best-known boat manufacturers as original equipment.

Look to Attwood for quality replacement parts and marine accessories.

SAVE THESE INSTRUCTIONS

Form Number 69230 Rev. D

FEATURES:

This base is designed for use with the Attwood 7100 Series All-Round

Lights and Attwood Combination Sidelights with an angled pole.

For 12-volt D.C. only.

CAUTION:

To prevent personal injury, always disconnect the power source when

installing or servicing this product. Always remove the boat from the

water before using 120V AC power tools.

INSTALLATION INSTRUCTIONS:

NOTE: For technical detailed positioning follow the standards of

navigation rules. Below (see Figure 1) are simplified drawings of

placement of navigational lights in relationship to one another.

Figure 1

Figure 2

Holes for

3 #10 Screws

•

1-3/8" Hole

•

Allow for

rotation of

swing cover

•

1. Position the light base either on the bow for combination sidelights

or the stern for all-round lights. Be sure that the mounting surface is

flat and that the selected area will accommodate the base dimensions.

2. Using the template provided (see Figure 2), locate the base center

line parallel to the boat fore-and aft center line and carefully mark

the center installation hole and the three screw holes. Drill 1-3/8"

diameter hole being very careful not to crack or break the gelcoat

finish around the edge of the hole. Drill the three screw holes.

Ensure no burrs are left around 1-3/8" hole.

NOTE: On some installations you may have to connect the wires then

push them back through wire hole prior to screwing down the base.

3. Apply sealant between deck and light base. Fasten base in place

with three stainless steel screws.

03-10

CAUTION: DO NOT OVERTIGHTEN SCREWS.

4. Wire as follows:

A. 911339 (2-wire base): Connect one black wire to the battery

ground (-) harness, using a crimp-on wire connector. Attach the

remaining black wire to the positive switched wire from the

navigation light switch.

B. 911639 (3-wire base): Connect black wire to the battery

ground (-) harness, using a wire connector. Connect the solid

gray wire to the wire from the switch for the anchor, courtesy, or

navigation light (depending on the light being used). Use a wire

connector to make the connection. Connect the black/gray wire

to the wire from the switch for the navigation, courtesy, or running

lights (depending on which light is used) using a wire connector.

NOTE: Follow instructions for specific light being used in this base

for wire connections.

C. All positive wires must be fused to protect the circuit. Tape

connections for added safety. MAKE SURE POWER SOURCE

IS 12-VOLT D.C. ONLY. HIGHER VOLTAGE CAN CAUSE

DAMAGE TO LIGHT AND WIRE CIRCUITRY.

5. Check the base function by first rotating the cover 90 , exposing

the hole for the pole. Insert the light pole into the socket and lock

in place by rotating cover 90 . Turn navigation running lights on

to make certain they function properly. Turn anchor or courtesy

switch on and make certain light works properly. Remove the

pole by rotating the cover 90 and, once pole is removed, rotate

the cover 90 forward to cover the hole, to keep dust and dirt out.

This product carries the standard Attwood one year warranty.

See Product Catalog for details.

FORWARD

•

1016 N. Monroe Street, Lowell, MI 49331-0260 www.attwoodmarine.com

Position on boat

center line when

installing combination

bow light

Position parallel to

and as close to the

boat center line as

practicable near the

transom when installing

all-around light