Atwood G10-3E Посібник - Сторінка 2

Переглянути онлайн або завантажити pdf Посібник для Водонагрівач Atwood G10-3E. Atwood G10-3E 17 сторінок. L.p. gas water heater
Також для Atwood G10-3E: Експлуатація та технічне обслуговування установки (17 сторінок), Інструкції з монтажу, експлуатації та технічного обслуговування (9 сторінок)

Друкувати сторінку

CRITICAL INSTALLATION WARNINGS

• Install in recreation vehicles only. RV's are recreation vehicles

designed as temporary living quarters for recreation, camping, or

travel use having their own power or towed by another vehicle.

• All combustion air must be supplied from outside the RV, and all

products of combustion must be vented to outside the RV.

•

vent water heater with venting system serving another appli-

DO NOT

ance.

•

vent water heater to an outside enclosed porch area.

DO NOT

• Protect building materials from flue gas exhaust.

• Install water heater on an exterior wall, with access door opening to

outdoors.

•

modify water heater in any way.

DO NOT

•

alter water heater for a positive grounding system.

DO NOT

•

HI-POT water heater unless electronic ignition system (cir-

DO NOT

cuit board) has been disconnected.

•

use battery charger to supply power to water heater even

DO NOT

when testing.

USA AND CANADA

FOLLOW ALL APPLICABLE STATE AND LOCAL CODES

IN THE ABSENCE OF LOCAL CODES OR REGULATIONS

• Recreation Vehicles ANSI A119.2/NFPA 501C.

• National Fuel Gas Code ANSI Z223.1 and/or CAN/CGA B149 Installation

Codes

• Federal Mobile Home Construction & Safety Standard, Title 24 CFR, part

3280, or when this Standard is not applicable, the Standard for Manufactured

Home Installations (Manufactured Home Sites, Communities and Set-Ups),

ANSI A255.1 and/or CAN/CSA-Z240 MH Series, Mobile Homes.

• National Electrical Code ANSI/NFPA No. 70 and/or CSA C22.1

• Park Trailers A119.5

• CSA standard Z240 RV Series, Recreational Vehicle.

GENERAL INSTALLATION

Below is the most common type of installation for the water heater.

However, there are other approved methods such as baggage com-

partment (refer to MPD 90093) and flush mounting installations (refer

to MPD 93948). Consult your Field Auditor, Account Manager, or the

Atwood Service Department if you have additional questions.

1. Locate water heater on floor of coach before erecting side walls.

The water heater tank must be permanently supported at the same

level as the bottom of sidewall cutout (by the floor or a raised floor).

2. To install water heater on carpeting, you must install appliance on a

metal or wood panel that extends at least three inches beyond the

full width and depth of appliance.

3. If water heater is installed where leakage of connections or tank will

damage adjacent area, install a drain pan which can be drained to

out side of coach, under water heater.

4. Connect both 1/2˝ NPT water lines - hot water outlet female

(

1-A) and cold water inlet female (

FIG

lines (

1-C).

FIG

a. Allow flexibility in water and gas lines so you can pull unit for-

ward through wall one inch past skin (

b. Seal gas line entrance opening by sliding grommet (

3/8˝ tubing (

1-F) before flaring tubing (

FIG

and grommet through opening in housing (

fitting (

1-E) and press grommet into opening. If gas line tubing

FIG

is already flared, cut grommet on one side. Place split grommet

over gas line and press it into opening.

c. Always use pipe lubricant on threads when connecting hot and

cold water couplings. A suitable plastic fitting is recommended.

PRODUCT DAMAGE

• Do not pull on main burner tube (

5. Erect side walls and cut opening. See chart and

Frame with 2x2 lumber (or equivalent).

REFER TO CURRENT STANDARDS OF

1-B) and 3/8˝ flared LP gas

FIG

1-D) onto

FIG

1-F). Pull gas line

FIG

1-C). Connect flare

FIG

CAUTION

9-C).

FIG

2-A & B.

FIG

CUTOUT

CAPACITY

Gallon

4 - 6

12-5/8˝

15-3/4˝

MINIMUM CLEARANCE FROM COMBUSTIBLE CONSTRUCTION

Sides:

0˝

Back:

0˝

6. Bend all flanges 90˚ along scored lines (

7. To prevent water leaks caulk thoroughly around opening, including

bend slots (

3-A). Butyl Tape (1˝x1/8˝) may be substituted for

FIG

caulking material.

8. Push unit against caulking, secure 4-corner brackets

coach with No.8 - 3/4˝ round head screws (not furnished) or equivalent.

Complete the installation by inserting the same type of #8 screws in the

holes provided around the flange of the water heater housing.

9. Attach access door (

FIG

a. Snap hinge pin (

FIG

b. Slide cover (

5-C) onto hinge pin.

FIG

c. Slide hinge pin into cover, snapping into clip at same time (

: To remove hinge pin, support access cover and apply force to

NOTE

corner of hinge pin as shown

10. Disconnect unit and its individual shut-off valve from gas supply

line during any pressure testing of system in excess of 1/2 PSIG

(3.4 kPa, 14˝ water column [W.C.]).

than maximum indicated on rating plate of gas valve (13˝ W.C.).

Isolate unit from gas supply line by closing its individual manual

shutoff valve during any pressure testing ≤ 1/2 psig.

FIRE AND/OR EXPLOSION

•

use matches, candles or other sources of ignition when

DO NOT

checking for gas leaks.

11. Turn on gas and check water heater and all connections for gas

leaks with leak detecting solution.

12. Fill water heater tank, check all connections for water leaks (

A & B).

PRESSURE-TEMPERATURE RELIEF VALVE

This water heater is equipped with a temperature and pressure relief

valve (

10) that complies with standard for Relief Valves and

FIG

Automatic Gas Shutoff Devices for Hot Water Systems, ANSI Z21.22.

This valve is a safety component and must not be removed for any reason

other than replacement.

place a valve, plug or reducing coupling on outlet part of

•

DO NOT

relief valve.

If you use a discharge line, do not use a reducing coupling or other

restriction smaller than outlet of relief valve. Allow complete drainage

of both valve and line.

FOR REPLACEMENT PARTS:

•

install anything less than a combination temperature-pressure

DO NOT

relief valve certified by a nationally recognized testing laboratory that

maintains periodic inspection of product of listed equipment or materi-

als, as meeting requirements for Relief Valves and Automatic Gas

Shutoff Devices for Hot Water Supply Systems, ANSI Z21.22. Valve

must have a maximum set pressure not to exceed 150 psi.

• Install valve into opening provided and marked for this purpose on

water heater.

• Installation must conform with local codes or in the absence of local

codes, American National Standard for Recreational Vehicles, ANSI

A119.2/NFPA 50IC.

• For an external electrical source, ground this unit in accordance with

National Electrical Code ANSI/NFPA70.

Your Atwood gas water heater is now ready for operation. Continue to

HOW TO OPERATE YOUR WATER HEATER.

Electronic Ignition

continue to

Pilot Relight continue to Pilot Relight WIRING INSTRUCTIONS.

CUT OUT DIMENSION

16-1/4˝

Top:

0˝

Bottom:

0˝

3).

FIG

5).

5-A) into clip (

5-B).

FIG

5-E.

FIG

set inlet pressure higher

DO NOT

WARNING

EXPLOSION

Electronic Ignition WIRING INSTRUCTIONS.

DEPTH

17-5/8˝

20-5/8˝

4-A to

FIG

5-D).

FIG