Aube Technologies TI044 Посібник з встановлення та експлуатації - Сторінка 2
Переглянути онлайн або завантажити pdf Посібник з встановлення та експлуатації для Таймер Aube Technologies TI044. Aube Technologies TI044 9 сторінок. Industrial indoor/outdoor solar timer
Також для Aube Technologies TI044: Посібник з встановлення та експлуатації (4 сторінок)
Друкувати сторінку
Automatic Mode
In Automatic mode, the TI044 controls Load 1 according to the
programmed schedule (see section 6). The mode indicator (AUTO),
the state (ON or OFF) and the current program number are
displayed.
To temporarily override the programmed schedule, press the MODE
button or use the remote switch (if connected). The new state
indicator will flash to show that this state is temporary. The override
remains in effect until you press the MODE button (or use the remote
switch) or until the beginning of the next program.
3.3
Load 2
Load 2 follows the sunset/sunrise program (regardless of the
operating mode of the timer). For example, if Load 2 is a light, the
light will turn On at sunset and turns Off at sunrise.
NOTE: To use Load 2, you first need to enter the city coordinates and
set the date (see section 6).
Setting the Clock
NOTE: The switch displays the time in 24-hour format by default or
following a reset.
To switch between 12-hour format and 24-hour format, proceed
as follows:
a) Press the MODE button to ensure the MAN or AUTO indica-
tor is displayed.
b) Briefly press the MIN and HOUR buttons simultaneously
(0:00 display = 24-hour; 12:00 display = 12-hour).
Set the time using the HOUR and MIN buttons. For the 12-hour
time format, if you are setting an afternoon time, ensure PM
appears on the screen.
Press the MODE button to return to normal operation.
Daylight Savings Time
This procedure sets the switch for daylight savings time or for stan-
dard time.
Press the CODE button four times.
Press the MIN button to switch between nor and Ad.
nor
Standard time / Normal time / Winter time
Ad
Daylight savings time / Advanced time / Summer time
Press the MODE button to return to normal operation.
Sunset/Sunrise Program
NOTE 1: Load 2 always follows the sunset/sunrise program.
Therefore, to use Load 2, you need to enter the city coordinates
(longitude and latitude) and set the date.
NOTE 2: By default, once you have programmed the sunset/sunrise
parameters, Load 1 will follow the sunset/sunrise program when you
place the timer in Automatic mode. To set your own schedule, see
section 7.
6.1
Determining the sunset/sunrise parameters
Fill out the following table:
Latitude
Longitude
1)
LATITUDE & LONGITUDE: Enter the coordinates of your city or
the nearest city using the supplied table. If none of the cities in the
TI044
Day #
nor/Ad
table is applicable, this information is usually available on the Inter-
net.
NOTE: Add a minus sign when entering a south latitude coordinate or
a west longitude coordinate.
2)
DAY #: Enter the day #. (Add the code of the current month to
the current date.)
For example: For June 24th, the day # = 151 + 24 = 175
January
February
March
April
3) nor/Ad: If your country has daylight savings time, select the cur-
rent time period.
nor
Ad
4.
4) Lc: If your city's time zone is based on political or economic
boundaries instead of its coordinates, your lights might switch On/Off
too early or too late with respect to sunset and sunrise. Therefore,
apply a correction factor (+1 or -1). Otherwise, leave it at 0.
6.2
Programming the sunset/sunrise parameters
Once you have completed section 6.1, proceed as follows:
Press the CODE button until the desired parameter appears.
The parameters appear in the following order.
Parameter
Latitude (LAT)
Longitude (LONG)
5.
Day number (DAY #)
Daylight savings time
Local correction factor (Lc)
Press the HOUR or MIN button to modify the value (see table
above for the buttons to use).
Press the MODE button to return to normal operation.
Programming the Schedule
NOTE: Applies to Load 1 only. The programmed schedule does not
affect Load 2 which follows the sunset/sunrise program only.
6.
The switch can hold 2 programs which are repeated every day. When
you place the timer in Automatic mode, it will activate the load at the
start of each program and deactivate it at the end of the program. You
need to set the following parameters:
Press the PGM button until the desired parameter is displayed.
If you have entered your city's parameters (see section 6), the
Lc
parameters P1 ON and P2 OFF show the sunset time and
sunrise time for this time of the year. If Load 1 is used for
lighting, when the timer will be placed in AUTO mode, it will turn
the light ON at sunset and will turn it Off at sunrise. For example:
0
May
120
31
June
151
59
July
181
90
August
212
Standard time / Normal time / Winter time
Daylight savings time / Advanced time / Summer time
Default
setting
00
000
-180 to 180 HOUR & MIN
000
nor
0
P1 ON
: Start time of program 1
P1 OFF : End time of program 1
P2 ON
: Start time of program 2
P2 OFF : End time of program 2
September
243
October
273
November
304
December
334
Possible
Buttons
settings
used
-65 to 65
HOUR & MIN
1 to 365
HOUR & MIN
nor / Ad
MIN
-1, 0, 1
MIN
7.
02/2014
2/4