3onedata IPS215 Series Посібник зі швидкого встановлення - Сторінка 2
Переглянути онлайн або завантажити pdf Посібник зі швидкого встановлення для Перемикач 3onedata IPS215 Series. 3onedata IPS215 Series 3 сторінки. Unmanaged industrial poe ethernet switch
Також для 3onedata IPS215 Series: Посібник зі швидкого встановлення (3 сторінок)
Друкувати сторінку
Step 1
Check if the DIN-Rail mounting kit is installed firmly.
Step 2
Insert the bottom of DIN-Rail mounting kit (one side
with spring support) into DIN-Rail, and then insert
the top into DIN-Rail.
Tips:
Insert a little to the bottom, lift upward and then insert
to the top.
Step 3
Check and confirm the product is firmly installed on
DIN-Rail, then mounting ends.
【Disassembling DIN-Rail】
Step 1
Device power off.
Step 2
After lift the device upward slightly, first shift out the
top of DIN-Rail mounting kit, and then shift out the
bottom of DIN-Rail, disassembling ends.
Notice before power on:
Power ON operation: First insert the power supply
terminal block into the device power supply interface,
and then plug the power supply plug contact and power
on.
Power OFF operation: First, remove the power plug,
and then remove the wiring section of terminal block.
Please pay attention to the above operation sequence.
【Power Supply Connection】
The serious of switches top panel provide
3-pin 7.62mm pitch industrial terminal
blocks, support 1 DC power input, with anti - reverse
connection function. Voltage range: 48VDC (45~55VDC). The
pin definitions of power supply are shown as follows:
Pin No.
Pin Definition
Description
1
V+
Positive power input
2
FG
Shell Ground
3
V-
Negative power input
【DIP Switch Settings】
The serious of switches panel provide 4-pin DIP
switch for function setting, where "ON" is enable
valid terminal. DIP switches definition as follows:
DIP
Definition
1
Flow control
2
100M copper port forced 10M
3
VLAN (ports 5 and 1-4 can
communicate with each other,
but ports 1-4 cannot
communicate with each other)
4
Reserved
【Checking LED Indicator】
The device provides LED indicators to monitor the device
working status with a comprehensive simplified
troubleshooting; the function of each LED is described in the
table as below:
LED
Indicate
Description
PWR is connected and running
ON
normally
PWR
PWR is disconnected and running
OFF
abnormally
ON/OFF
The device is running abnormally
RUN
Blinking
The device is running normally
POE ports supply electricity for
POE
ON
other devices normally
（1-4）
OFF
POE port is not powering other
LED
Indicate
ON
Link/Act
Blinking
（1-5）
OFF
【Specification】
Panel
Operation
100M fiber port
Set the DIP to
ON
100M copper port
Set the DIP to
ON
Set the DIP to
ON
100M PoE port
-
POE pins
Indicator
Switch Property
Backplane bandwidth
Packet buffer size
MAC Address Table
Power Supply
Description
devices
The
Ethernet
interface
has
established an active network
connection
The Ethernet interface is in a
network activity state.
The Ethernet interface has not
established an active network
connection.
100Base-FX, interfaces support
SC/ST/FC optional
10/100Base-T(X) self-adapting
RJ45
port,
half/full
duplex
self-adapting
or
compulsive
working
mode,
support
MDI/MDI-X self-adapting
10/100Base-T(X) self-adapting
RJ45
port,
half/full
duplex
self-adapting
or
compulsive
working
mode,
support
MDI/MDI-X self-adapting, the
maximum power of single PoE
port is 30W
V-,
V-,
V+,
V+
are
corresponding to Pin 1, 2, 3, 6
Running
Indicator,
Port
Indicator,
Power
Supply
Indicator, PoE Indicator
1.6G
1Mbit
2K