ADDER ALIF100T Швидкий старт

Переглянути онлайн або завантажити pdf Швидкий старт для Подовжувач ADDER ALIF100T. ADDER ALIF100T 2 сторінки.

Друкувати сторінку

Safety information

• For use in dry, oil free indoor environments.

• Not suitable for use in hazardous or explosive environments or next to highly flammable materials.

• No user serviceable parts are contained within the module - do not dismantle.

Radio Frequency Energy

All interface cables used with this equipment must be shielded in order to maintain compliance

with radio frequency energy emission regulations and ensure a suitably high level of immunity to

electromagnetic disturbances.

European EMC directive 2014/108/EC

This equipment has been tested and found to comply with the limits for a class A

computing device in accordance with the specifications in the European standard EN55032.

In a residential environment, this equipment may cause radio interference.

FCC Compliance Statement (United States)

This equipment generates, uses and can radiate radio frequency energy and if not installed and used

properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to

radio communication. It has been tested and found to comply with the limits for a class A computing

device in accordance with the specifications part 15 of FCC rules, which are designed to provide

reasonable protection against such interference when the equipment is operated in a commercial

environment. Operation of this equipment in a residential area may cause interference, in which case

the user at his own expense will be required to take whatever measures may be necessary to correct

the interference. Changes or modifications not expressly approved by the manufacturer could void the

user's authority to operate the equipment.

Canadian Department of Communications RFI statement

This equipment does not exceed the class A limits for radio noise emissions from digital apparatus set

out in the radio interference regulations of the Canadian Department of Communications.

Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables aux

appareils numériques de la classe A prescrites dans le règlement sur le brouillage radioélectriques publié par le

ministère des Communications du Canada.

Web:

Contact:

Support:

Part No. MAN-QS-ALIF-ADDER_V1.2

www.adder.com

www.adder.com/contact-us

www.adder.com/support/contact-support

AdderLink Infinity 100T

Welcome

This quick start guide covers some of the key points of the ALIF100T unit. Full user details and setup

instructions can be found at www.adder.com/en/kvm-solutions/adderlink-infinity-100t

Initial configuration

Please see the next page for Connection details.

ALIF units can be linked in two mains ways: Direct or Networked.

Direct linking

Where ALIF transmitters and receivers are directly linked to each other, very little configuration action

is required, provided that they both have their factory default settings in place - just link them together.

If the standard settings have been changed in a previous installation, you merely need to perform a

manual factory reset on each unit. Please see the next page for further details.

ALIF100T

Networked linking

Where ALIF units are connected via networked links, you can either configure them individually, or

configure them collectively using an A.I.M. server:

• Configuring networked ALIF units individually - You need to specify the network addresses

of the ALIF units so that they can locate each other. This is done by running the AdderLink Infinity

browser-based configuration utility on a computer system linked to the same network as the ALIF

units. Please see the next page for further details.

• Configuring networked ALIF units collectively - The AdderLink Infinity Management (A.I.M.)

server allows you to configure, control and coordinate any number of ALIF transmitters and

receivers from a single application. See adder.com for details.

Note: If you are using one or more ALIF100T transmitters

within an installation managed by an A.I.M. server, the A.I.M.

server must be running firmware version 4.7 or above.

Gigabit

ALIF100T

Ethernet

IMPORTANT: When using A.I.M. to configure ALIF units, it

is vital that all units that you wish to locate and control

are set to their factory default settings. Otherwise they will

not be located by the A.I.M. server. If necessary, perform a

manual factory reset on each ALIF unit. See next page.

Quick Start

ALIF RX

continued overleaf