3onedata ICPE2300A-BW-8A25-1GC3GT-PD2P12 48 Посібник зі швидкого встановлення - Сторінка 3

Переглянути онлайн або завантажити pdf Посібник зі швидкого встановлення для Мережевий маршрутизатор 3onedata ICPE2300A-BW-8A25-1GC3GT-PD2P12 48. 3onedata ICPE2300A-BW-8A25-1GC3GT-PD2P12 48 5 сторінок. Industrial indoor 5g wireless router

then remove the wiring section of terminal block. Please
pay attention to the above operation sequence.
【Power Supply Connection】
PoE power supply
The WAN port of this device supports PoE power receiving,
which conforms to IEEE802.3af/at standard.
12~48VDC power supply
The device provides 6-pin 5.08mm pitch power
supply terminal blocks and power supply
occupies the top 4 pins. It supports two
independent DC power inputs, V1 and V2. The
device supports redundant power supply, two
independent power supplies can work at the
same time. The device will still run non-stop when one power
supply fails. The power supply supports non-polarity
connection, and the equipment can still work normally after
reverse connection. The definitions of power pin are shown in
the left figure, and the power input range is 12~48VDC.

【Relay Connection】

This device provides 6-pin 5.08mm pitch terminal
blocks, relay occupies the lower 2 pins. Relay
terminals are a set of normally open contacts of
the device alarm relay. They are open circuit in
the state of normal non alarm, closed when any
alarm
information occurs.
externally connect to alarm lights or alarm buzzer or other
switching value collecting device in order to timely notify
operators when the alarm occurs. (This function is reserved).
【Reset Button Setting】
The device provides 1 RESET button, press the
RESET button for 1~2s and release it, and the device
will restart automatically; Press and hold the RESET
button for 5s and release it, and the device will automatically
restore the factory defaults.
【Console Port Connection】
The device provides 1 program debugging port based on
RS-232 serial port which can conduct device CLI command
management after connecting to PC. The interface adopts
RJ45 port, the RJ45 pin definition is as follows:
Pin No.
2
Definition
TXD
【USB Port Connection】
This device provides 1 Type-A USB 2.0 Female,
this interface is reserved.
【Mounting SIM Card】
This device supports 1 SIM card slot which can
insert 1 Micro SIM card and 1 Nano SIM card , 1
Micro-SD card, in which SD card is reserved.
Notice:
If the SIM card needs to be changed, the device should
be power off first in case of damaging the card.

【Antenna Connection】

The antenna specifications provided by the device are shown
below:
Type
2.4G wireless
5.8G antenna
5G Antenna
The relay
can
Magnetic sucker base
Magnetic base with sucker 3005040115
【Checking LED Indicator】
The device provides LED indicators to monitor its operating
status, which has simplified the overall troubleshooting
process. The function of each LED is described in the table
below:
LED
Indicate
ON
RUN
Blinking
3
5
RXD
GND
Gain
Quantity
P/N
(dBi)
(pcs)
3005040101
5
2
3005040102
5
2
3005040098
3
4
3005040090
4
4
Description
The device is powering on or the
device is abnormal.
The device is running normally
3 / 5
LED
Indicate
Description
The device is powered off or the
OFF
device is abnormal.
ON
Device restore factory setting alarm
ALM
OFF
Without device alarm
ON
Power P1/P2 is running normally
P1-P2
Power P1/P2 is disconnected or
OFF
running abnormally
ON
Wireless WiFi network is enabled
Wireless WiFi is in an active
2.4G/
Blinking
network status
5.8G
Wireless WiFi network is running
OFF
abnormally or turned off
The indicators are all off, indicating
that no 2.4G/5.8G bridge has been
established.
One indicator is on. It means
2.4G/5.8G signal at the opposite
end is weak
All indicators are on. It means
2.4G/5.8G signal at the opposite
end is strong
LAN/WAN port connection has
ON
established
a
connection
LAN1-
LAN/WAN port is in network active
LAN3
Blinking
status
/WAN
LAN/WAN port connection has not
OFF
established
a
connection
PoE power input in WAN port is
ON
normal.
PoE
WAN port has no PoE power input
OFF
or is receiving power abnormally
ON
5G network is enabled
5G network is in an active network
5G
Blinking
status
OFF
5G network is running abnormally
valid
network
valid
network