Danfoss 324166 Встановлення та експлуатація

Переглянути онлайн або завантажити pdf Встановлення та експлуатація для Контролер Danfoss 324166. Danfoss 324166 3 сторінки. Wireless floorheating controller and room thermostat, type cf

Друкувати сторінку

Installation and operation

Temperature setting

Set room temperature on the thermostat dial. On

the right-hand side of the thermostat is a func-

tion switch with 3 possible settings:

Sun : The room temperature will be as set on the

thermostat.

Clock : Used only if the zone regulator is en-

gaged. The temperature will be as set on the

room thermostat, but in accordance with the

consumption pattern entered.

The consumption pattern in the zone regulator

can be overridden by moving the switch to sun or

moon.

Moon : The room temperature will be as set on

the thermostat - minus 5°C.

Limitation of the setting range

Behind the button for temperature setting are two

lock-pins. These can be placed in the setting

knob as shown in fig. 4 if the thermostat setting

range is to be narrowed.

Putting into operation

Each room thermostat has a unique ID number

preventing conflicts with other thermostats.

A single room thermostat is capable of regulating

several heating outputs, provided these outputs

are assigned to the thermostat.

Assigning thermostats to output(s)

-The installation cable between room thermostat

and CFM (fig. 2) must be connected in assigning

each thermostat to the respective output(s).

-In the LED array the first available output will

flash. The LED in the CFR will also flash. Out-

puts already assigned will not be lit (fig. 2). By

pressing OK the thermostat will be assigned to

that output. If the room thermostat is to be as-

signed under another lit output, scroll to the out-

put by means of the +/- keys, then press OK.

-When the installation cable is removed, the red

LED behind the front panel (fig. 4) will flash for at

least 4 minutes. See "Test of room thermostat"

Removal of assigned thermostat

-It is not necessary to have the installation

cable in place when removing an assigned ther-

mostat. Once a thermostat has been removed, it

may be reassigned to another output.

-Removal of room thermostat is done by pressing

OK for 5 seconds, then the entire LED array will

be lit. Scroll to the specific room thermostat to

be removed with the +/- button,and press OK for

5 seconds. The thermostat has now been re-

moved.

Test of room thermostat

If a defect in a room thermostat is suspected, the

following test may be carried out:

Wireless floorheating controller and room thermostat, type CF

- Set the thermostat to the highest temperature.

- Move the function switch on the side of the

room thermostat to a new position.

- If the LED behind the front panel (fig. 4)

flashes quickly for 4 minutes, the room thermo-

stat is OK.

Battery change

If the battery is getting low, the LED will flash 6

times every 6 seconds. See fig. 4.

Master regulator CFM

This regulator governs the individual heat cir-

cuits via wireless communication with the asso-

ciated room thermostats. Connection of 8 heat

circuits is enabled.

If more heat circuits are required, connect one

or max. two slave regulators CFS, each with

connection for 8 circuits. This allows max. 24

heat circuits to be governed.

The master/slave is to be fitted immediately

above the distributor pipe on the wall or in a dis-

tribution cabinet. Easy access to plugs and ter-

minals should be ensured. See instruction draw-

ing on the opposite page.

If two slave regulators are connected, move the

jumper in "slave 2" to position 2. See instruction

drawing.

The connection cable for the slave regulator is 1

m. Cable lengths of up to 100 m are enabled

(available from your electrical items wholesaler)

Alarm

There are 2 options with respect to alarms given

by the master regulator:

-Integral acoustic signal can be selected by

moving the jumper marked "buzzer" from OFF

to ON. See installation drawing.

-External alarm generator can be connected to

the output marked

Technical data

Max. ambient temperature 60°C.

Enclosure IP40

Zone regulator CFZ

The zone regulator governs a maximum of 6

heat zones. For each heat zone, individual tim-

ing programmes can be connected. For reading

and operating convenience, it is recommended

to place the regulator at eye height.

The connection cable is 5 m. Cable lengths up

to 100 m are permitted (available from your

electrical items supplier).

Troubleshooting

Appearance

Problem

Reason/cause

CFM controller out-

Lack or ex-

Distance between room and

put array blinks

cessive heat

master is too far.

specifically from a

to floor heat-

row and column(s)

ing system

Degradation of signal due to

reinforced concrete or foil

faced insulation between

floors.

External antenna mounted

close to metal parts or wires.

Master control is placed in

metal enclosure.

Alarm symbol in

zone controller,

Interference from electronic

CFZ flashes

equipment using the same

frequency, 433.92Mhz (i.e.

baby monitors, portable or

wireless headphones)

Acoustic alarm

Room tem-

Low battery

buzzes (provided

perature is

jumper is set to

Problem in heating system

below 6

"ON")

or signal to thermostat

(43

Master or slave

Blown fuse in master/slave

No heat

controller row(s)

and entire columns

Loose wire connection be-

lit on master output

tween master and slave con-

array

troller

Constant light in

No heat

Defective zone actuator

LED array

Lack of heated fluid to sys-

tem

LED on back of

Lack or ex-

Faulty battery

room thermostat

cessive heat

does not blink dur-

to floor heat-

Bad contacts between bat-

ing test mode

ing system

tery and thermostat

Defective room thermostat

All output LEDs are

No heat

Improper wiring

unresponsive

Master controller is defective

CFM controller out-

None

Normal operation during test

put array blinks rap-

of room thermostat

idly 3 times specifi-

cally from a row

and column(s)

Solution

Comments

Reposition thermostat in

If signal is

room until signal is clear.

continuosly

poor contact

Reposition external an-

Danfoss

tenna, however if signal is

still unclear move external

antenna to the

same floor as

thermostat(s)

Reposition room thermo-

stat and run test mode

Mount external antenna if

not already installed.

Eliminate interfering elec-

tronic equipment

Replace battery and test

thermostat

Max. load for

CFM 6W,

Check heating supply to

max. Load

the system and the circu-

for CFS 3W

lator pump

Check master control,

CFM, is properly wired.

First check actuators for

proper wiring then re-

place fuse in

master/slave controller,

1.25A

Check wire and connec-

tion between master and

slave

Replace zone actuator

Check heating supply to

the system and the circu-

lator pump

Replace battery/

Adjust connection in ther-

mostat to ensure better

contact to battery

Replace room thermostat

Check wiring of power to

CFM

Replace master control-

ler.

www.danfoss.com

DKCD 5/2002