AOG L series Посібник із швидкого старту
Переглянути онлайн або завантажити pdf Посібник із швидкого старту для гриль AOG L series. AOG L series 2 сторінки. Stand alone outdoor gas grill
Також для AOG L series: Посібник із швидкого старту (2 сторінок), Посібник із швидкого старту (2 сторінок)
Друкувати сторінку
"L" Series
CAUTION: For your safety read the installation instructions and owner's manual provided with the grill.
1-Safety
INSTALLER: Leave these instructions with consumer.
This grill must be installed in accordance with local codes and ordinances, or, in the absence of local codes, with either the latest National Fuel Gas Code (ANSI
Z223.1/NFPA 54), and Natural Gas and Propane Storage and Handling Installation Code (CSA-B149.1).
This appliance and its individual shutoff valves must be disconnected from the gas-supply piping system when testing the system at pressures in excess of ½ psig.
This appliance must be isolated from the gas-supply piping system by closing its dedicated manual shutoff valve during any pressure testing of the gas-supply
system at pressures up to and including ½ psig.
WHEN INSTALLING AND OPERATING THIS APPLIANCE WITH PROPANE (L.P.) GAS, ALL INSTRUCTIONS AND WARNINGS IN YOUR OWNER'S MANUAL
MUST BE OBSERVED. FAILURE TO DO SO MAY RESULT IN A FIRE OR EXPLOSION CAUSING SERIOUS INJURY OR DEATH.
This grill is designed for outdoor use only. DO NOT use this grill inside a building, garage, enclosed area, or under any overhead construction. DO NOT
use this grill in or on a recreational vehicle or boat.
Installation must be performed by a qualifi ed professional service technician.
2-Unpacking
Carefully unpack the grill, removing all packing material and protective fi lm. Verify that all
parts have arrived undamaged by consulting the parts list in the owner's manual. Remove
foam packed hardware from oven area. (See Fig. 2-1.)
Consult the parts list in the owner's manual. If any parts are missing or damaged,
immediately contact the AOG dealer before beginning installation.
3-Installation
Location
Locate the grill on a flat level surface. Refer to the INSTALLATION
REQUIREMENTS section of your grill owner's manual for complete details.
CAUTION: Wind blowing into or across the rear oven lid vent (Fig.
3-1) can cause poor performance and/or dangerous
overheating. Orient the grill so that the prevailing wind
blows toward the front of the grill (Fig. 3-2).
CAUTION:
To prevent dangerous overheating, the rear of the unit must have
a minimum clearance of 4" from any non-combustible wall.
Connect Gas supply
These quick start instructions assume a
propane cylinder confi gured unit. See main
instructions for natural gas or household
propane confi gured units.
Place approved propane 20lb cylinder in tank
tray and secure in position (Fig. 3-3).
Connect quick coupler hose and regulator
supplied with unit to propane cylinder (Fig.
3-4).
Set all burner control valves to OFF and
open gas source control valve.
Follow the lighting instructions on the
reverse side of this guide.
Proper grill airfl ow must be maintained as
shown in Fig. 3-5.
REV 0 - 1602080910
Outdoor Stand Alone
CONSUMER: Retain for future reference.
Sideburner
shelf (if
equipped)
Quick
coupler
Tank support sleeve
Fig. 3-3
Gas Grill
Quick Start Guide
Lift out foam packed hardware
INCORRECT
Rear oven lid vent
YOU MUST PROTECT REAR OVEN
VENT FROM PREVAILING WIND
Fig. 3-1
Regulator
Backburner
(if equipped)
Vent
Hose
Fig. 3-4 Type I Acme thread quick coupler
Maintain proper
Propane
ventilation airfl ow
cylinder (tank)
Fig. 3-5
Remove plastic
zip-ties
Fig. 2-1
CORRECT
PLACE GRILL SO PREVAILING WIND
BLOWS TOWARD FRONT OF GRILL
Fig. 3-2
Hand wheel
Brass Acme
thread fi tting
U
L
Liquid level
indicator
Hand nut with
(optional)
Acme thread
To connect the regulator/
hose assembly to the
propane-gas cylinder
valve fitting: Press the
hand nut on the regulator
over the Acme thread fi tting
on the cylinder valve. Turn
the hand nut clockwise to
engage the threads and
tighten until snug.
QCC
Type 1
valve
Pressure
relief
valve
L-C2-482