AOI UCS-Q1 Короткий посібник користувача - Сторінка 2
Переглянути онлайн або завантажити pdf Короткий посібник користувача для Вимірювальні прилади AOI UCS-Q1. AOI UCS-Q1 2 сторінки.
Друкувати сторінку
g. Strobe Power Control Knob
Setting
STBY
1
2
Strobe
OFF
1/64
1/32 1/16 1/8 1/4 1/2 1/1
Power
h. Strobe Test
1 x
Diffuser Installation
a.
Attaching
b. Detaching
(i)
(ii)
Fiber Optic Cable Connection
Insert one end of the Fiber Optic Cable into UCS-Q1 Fiber Optic Cable Port and
the other end to fiber optic port of the camera housing.
Fiber Optic Cable Port
i. Modeling Flash
If shooting in extremely bright ambient light conditions, the LED light may not be
bright enough for targeting purposes. Press and hold the
and the strobe will emit a bright, high frequency stroboscopic pulse for about 2
seconds. This rapid firing of the strobe will help in targeting the subject in bright
ambient light conditions.
When using the Snoot (AOI SNT-01, optional accessory sold separately), the
3
4
5
6
7
Modeling Flash also serves as a target light.
j. Flash Synchronization
The UCS-Q1 will analyze your camera's flash and automatically synchronize after
the first test shot. First, power on the strobe and select any Strobe Power setting
from 1-7 and take a single test shot. The UCS-Q1 will analyze the 1
memorize the Flash Synchronization setting for your camera. If you change
cameras or flash settings on your camera, simply power off the UCS-Q1, power on
and take another test shot to synchronize with your new camera or camera
settings.
k. Thermal Control
The UCS-Q1 is equipped with the overheat protection circuit. If the strobe has
been in continuous use, the internal electronics temperature may increase, the
recharging time / recycle time will slow down automatically．If the overheat
protection circuit is activated and the Indicators
alternately (see Table 1, Page 9). The strobe will be suspended temporarily. After
cooling down, the Indicators
will be resumed.
Blue
Blinking
- 7 -
Care and Maintenance
a.
Rinse the strobe exterior thoroughly with running fresh water after every use.
Pushing buttons and rotating knobs repeatedly in fresh water to eliminate
trapped salt water or debris.
b.
Clean the O-rings and the O-ring grooves at a regular time, and apply a small
amount of silicone grease (AOI SIR-5) to lubricate the O-rings.
c.
Dry well and remove the batteries prior to travel and storage.
IMPORTANT: Wipe the strobe dry and keep seawater away prior to opening the
battery cap. Do not allow seawater to be in contact with the interior parts of the
battery compartment, otherwise it may cause rust, corrosion or malfunction.
If seawater leaks into the battery compartment, please turn off the power and
remove the batteries immediately. Rinse the battery compartment with fresh water
before bringing it back to your local dealer / service center for further assistance.
- 10 -
button for 1 second
st
test shot and
and
will blink Blue & Purple
and
will be back to normal and all the functions
Purple
Blinking
- 8 -
- 11 -
l. Indicators Summary
Table 1
Indicator
Indicator
Blue Slow Blinking
Blue Rapid Blinking
Blue Still
Green Still
Yellow Still
Red Still
Red Rapid Blinking
Blue and Purple Blinking Alternately
Off
Purple Still
When Indicator
is Red Rapid Blinking (Battery Level below 10%), the strobe may
power down at any time.
Specifications
Model Number
AOI UCS-Q1-BLK / WHT
Description
Underwater Ultra Compact Strobe
Main Body Material
Polycarbonate + Glass Fiber
Waterproof Level
60 Meters / 200 Ft.
Guide Number
Color Temperature
Beam Angles
Horizontal- 85°, Vertical- 85° (with Diffuser)
Strobe
Flash Recharge Time
0.85 Second (Full Power)
1,800 Times Full Flash
Number of Flashes
(with 3500mAh Li-Ion Batteries)
Flash Synchonization
Self Learning during Power On Each Time
Maximum Output
700 Lumens
Color Temperature
LED
Beam Angles
Lights
160 Minutes (Max. Brightness with
Burn Time
3500mAh Li-Ion Batteries)
18650 Li-Ion Rechargeable Battery x 2pcs,
Min. Output Current: 5A,
Battery Requirements
Min. Battery Length: 69mm
(Batteries Not Included In Product)
Strobe Mounting
1" Ball Mount Only (Irreplaceable)
Dimensions
125.0mm (L) X 77.0mm (W) X 131.0mm (H)
On Land : Approx. 550g (Batteries Included)
Weight
Underwater : Approx. 90g (Batteries Included)
Main Seal O-Rings x 2pcs,
Accessories
O-Ring Remover, Silicone Grease,
Battery Storage Case (Batteries Not Included)
*Specifications and Appearances are subject to change without prior notice.
Description
Strobe Standby
Flash Recharging
Flash Ready
Battery Level 50% - 100%
Battery Level 25% - 50%
Battery Level 10% - 25%
Battery Level below 10%
Strobe Over Heated
Electronics Failure
-9 -
22
5600K
5600K
45°
6E010230-00001
- 12 -