Casio 1174 Посібник з експлуатації

Переглянути онлайн або завантажити pdf Посібник з експлуатації для Дивись. Casio 1174. Casio 1174 4 сторінки. Casio watch user manual

Друкувати сторінку

MO0603-EA

About This Manual

•

General Guide

• You can use the Remote Control functions while in the Timekeeping Mode.

• Press C to change from mode to mode. Each mode is explained in detail on the

following pages.

Timekeeping Mode

•

Timekeeping Mode

Signal Emitter

•

About the Timekeeping sub-modes

The Timekeeping Mode is made up of four sub-modes. Use the B button while in the

Timekeeping Mode to switch between the sub-modes.

• If you leave the watch in the TV, Video or Learning Mode without performing an

operation for about two or three hours, the watch automatically returns to the Normal

Timekeeping Mode.

• To manually return to the Normal Timekeeping Mode, press C to change to the

Calculator Mode. Next, use C to change to the Timekeeping Mode.

Press B.

Normal Timekeeping

Mode

About the TV and Video Tape Deck remote control function

In order to be able to use this watch for remote control of a television or video tape

deck, you must first set the appropriate manufacturer code. The manufacturer code

tells the watch what signals to use for remote control. The Manufacturer Code Table

shows the names of the manufacturers that correspond to each code. For full details

on how to actually set the manufacturer code, see "To set the manufacturer code".

Some TV or tape deck models may not work properly with this watch,

even though they are made by one of the manufacturers in the

Manufacturer Code Table. Also, you may find that you can control a TV or

tape deck using a code for a manufacturer that is different from the ones

in the table. For details on finding the code you should use, see "How to

find the right code".

Notes

• Replacing the battery will cause the remote control data setting (TV/video

manufacturer codes) to be altered. Be sure that you make a note of your codes

before you have the battery replaced.

• There are some manufacturers with more than one code. Try the various codes

available for your equipment to find the one that works best.

• You have to set separate codes for your TV and tape deck, even if they are made by

the same manufacturer.

• You might not be able to use this watch to control models that combine a TV and

tape deck into a single unit, multi-functional TVs that can be used as computer

monitors, or other televisions or tape decks equipped with special functions.

Operation Guide 1174

• Button operations are indicated using the letters shown in

the illustration.

Calculator Mode

•

In addition to normal timekeeping, the Timekeeping Mode

also provides you with remote control capabilities for your

TV, video tape deck, and other devices equipped with a

remote control unit.

• This watch only controls devices equipped with a remote

control unit.

• For details on how to set the time and date, see "To set

the time and date".

Note

The explanations in this manual use button symbols (K,

), button markings (

, etc.), and letters

(A, B, etc.) to indicate buttons on the watch.

Example: Press D to switch on the television.

TV Mode

Video Mode

(for television

(for video tape deck

remote control)

• After you perform an operation in any mode, pressing C returns to the Timekeeping

Mode.

• An input tone sounds each time you press a button. You can switch the confirmation

tone on and off in the Calculator Mode.

Manufacturer

FERGUSON

FUNAI

GOLDSTAR

GRUNDIG

HITACHI

JVC

MITSUBISHI

NEC

PANASONIC

Manufacturer

AKAI

FERGUSON

FUNAI

GOLDSTAR

LEARN

GRUNDIG

HITACHI

Learning Mode

JVC

(for remote control

of other devices)

MITSUBISHI

NEC

NOKIA

To set the manufacturer code

TV Mode indicator

Signal Emitter

SET

Manufacturer code

4. While the TV or video manufacturer code setting display is shown, press K to

increase the code number.

• Holding down K increases the code number at high speed.

• See the Manufacturer Code Table for details on manufacturer codes.

Alarm Mode

•

Manufacturer code (TV)

Code

Manufacturer

17, 18

PHILIPS

15, 16, 41, 42

PIONEER

06, 12, 13, 29, 32

SAMSUNG

20, 21, 22

SANYO

03, 25, 26, 27, 28, 29

SHARP

03, 04, 05, 30

SONY

03, 19

TELEFUNKEN

03, 29, 31, 32

TOSHIBA

02, 08, 09, 10

Manufacturer code (video tape deck)

Code

Manufacturer

24, 25, 33

PANASONIC

17, 18

PHILIPS

PIONEER

SAMSUNG

20, 21, 22

SANYO

04, 27, 42

SHARP

03, 04, 05

SONY

06, 19

TELEFUNKEN

28, 29

TOSHIBA

1. Switch on the TV or video tape deck whose

manufacturer code you want to set.

2. In the Timekeeping Mode, press B to select the TV

Mode (

) or Video Mode (

• Select TV Mode if you want to set the code for your TV,

or the Video Mode to set the code for your video deck.

3. Hold down A until a manufacturer code appears

flashing on the display.

5. To test whether or not the displayed manufacturer code

is correct for your equipment, point the Signal Emitter

(red window) at your TV or tape deck and press D.

• If the above operation switches the power of your TV or

tape deck off, it means that the correct code has been

selected.

• Certain TVs and tape decks may be slow to respond

after receiving a remote control signal. With such units,

try holding down D for one or two seconds.

• If nothing happens when you press D, use steps 4 and

5 to try another code.

Stopwatch Mode

•

Code

06, 28

06, 12, 14, 15, 29, 32

03, 35, 36, 40

01, 03, 37

03, 07

23, 24

03, 38, 39, 40

Code

02, 14

07, 08, 09, 10

16, 32, 33

34, 35, 36, 37, 38

11, 12, 13

06, 23

39, 40, 41