Free Spirits Electronic Jet Kit Інструкція

Переглянути онлайн або завантажити pdf Інструкція для Аксесуари для мотоциклів Free Spirits Electronic Jet Kit. Free Spirits Electronic Jet Kit 4 сторінки. For harley davidson 2012-13 vrod models

Друкувати сторінку
Electronic Jet Kit™ Instructions
Thank you for choosing the Free Spirits Fuel Injection Module, the module.
"ONLY"
The module is
usable for the following Harley Davidson models:
• 2012-13 Vrod Models
This is an Electronic Jet Kit. Like jet kits in the past, the more you modify, the more responsibility you take in
getting your fuel curve right. Going to www.freespirits.it for more information
INSTALLATION PREP
• Install Time: 60 minutes
• Required Tools for:
....Disconnecting the negative terminal of the battery.
.... Removing your seat
.... Loosening and propping up the fuel tank
Some vehicle modifications with Techlusion Inc. products
must not be used on public roads and in some cases may
be restricted to close course competition. Those products
not identified as US EPA legal are intended for off-road or
marine applications only. Not intended for use on emission
controlled vehicles.
Free Spirits
Telephone 0039 (0) 445-390437
Fax 0039 (0) 445-395539
1. Before installing the EFI you must first disconnect the negative lead from the battery.
2. Determine a location for the EFI unit. Suggested locations is on top of battery.
3. Remove tank shell, left and right front frame covers and horn assembly.
4. Locate and disconnect the IAT sensor.
5. Use a screwdriver to disengage the 8 clips retaining the airbox lid. The front clip is not visible
6. Remove the plastic nut, air filter cover and filter.
7. Locate and disconnect the rear crankcase breather hose inside air box and push through air box floor.
8. Slide the large O rings up the stacks to access the stack mounting screws. (The O rings retain
9. Disengage the front crankcase breather hose and remove the airbox floor. There is no clamp on
10. Disconnect the factory injector connectors from the fuel injectors. Connect the TFI fuel injector harness inline with
11. The front factory O2 connector is located inside the left radiator cover. Remove the screw
12. The rear factory O2 connector is located at the left rear of the tank shell. With the shell removed
13. Connect the TFI ground lead to negative terminal of battery along with factory ground lead.
14. Re-assemble any removed parts to complete the installation.
Free Spirits
Site: www.freespirits.it
1
2
Electronic Jet Kit™ Instructions
INSTALLATION - Please call technical support for any installation question.
Use supplied Velcro patch to securely mount the controller TFI.
and must be reached from the left side.
the screws should they become loose.) Remove the 6 screws and the velocity stacks.
this hose.
the factory fuel injectors connector and the factory fuel injector.
IMPORTANT: The TFI injector harness with the white/yellow wires must go to the front cylinder.
The EFI injector harness with the green/gray wires must go to the rear cylinder.
We recommend the EFI injector harness run along the left side of the frame backbone to the injectors
IMPORTANT: Make sure all connections are firmly secure and allow a little slack at the connections to prevent
engine vibration from damaging/breaking a wire on the
located on the bottom of the cover and slide the cover away from the radiator to access the O2
connector. Disconnect the sensor and plug in the white EFI bypass into the wiring harness.
it should be visible under the existing wiring. Locate the rear factory O2 connection which uses black connectors.
Disconnect it and install the black EFI bypass.
Telephone 0039 (0) 445-390437
Fax 0039 (0) 445-395539
harness.
Site: www.freespirits.it