Freedom Freedom 200+p Посібник користувача - Сторінка 3

Переглянути онлайн або завантажити pdf Посібник користувача для Автосигналізація Freedom Freedom 200+p. Freedom Freedom 200+p 7 сторінок.

Друкувати сторінку

seconds. The LED Status Light will change to flashing one to five times between pauses,

which indicates which protected zone triggered the system. The LED Status Light will

continue flashing this violation code until the ignition key is turned "on", thus clearing the

system's LED Status Light memory circuit. If desired, the system may be programmed for

30 second activation cycles instead of 60 second activated cycles.

Disarming The Security System

While the security system is in the armed condition, pressing the large transmitter button

once will instantly disarm the system and unlock the doors, provided an optional interface

was installed. Disarming is confirmed by the siren chirping twice and the parking lights

turning on for 30 seconds to illuminate the way to your car, except under the following

conditions: first, the parking lights will turn off 10 seconds after a door is opened, and

second, the parking lights turn off instantly when the ignition is turned "on".

However, if the security system was activated and reset while you are away, the disarm

confirmation will change to 4 siren chirps, 4 parking light flashes, and then the parking lights

will stay on for 30 seconds. The alarm will have this response upon every disarming until

the ignition switch is turned "on", which will clear the LED Status Light memory.

Anytime the security system activates, the LED Status Light will indicate which

protected zone caused the activation by flashing one to five times between pauses. This code

will continue to flash, even after disarming, until it is cleared by turning the ignition switch

"on". The system can retain up to five violation codes in its memory.

Remote Panic

In a threatening situation, the transmitter may be used to fully activate the system,

sounding the siren, flashing the parking lights and relocking the doors (if configured with

a doorlock interface). Even if the ignition is on, Remote Panic can be activated by pressing

and holding the transmitter's large button for two seconds. The system will automatically

reset after 60 seconds, or the transmitter's large button may be pressed and released again

to deactivate the Remote Panic feature.

The Valet Switch And Valet Modes

The Valet Switch may be used to keep the security system from actively or passively

arming during extended stopovers at service stations, for maintenance, valet parking, car

washing, etc., by placing the system into Valet Mode. There are two forms of Valet Mode:

first is Easy Valet

, whereby a disarmed system may be placed into Valet Mode without

the ignition key, and the second form is Valet Override, which will disarm an armed or

activated system and requires the use of the ignition key.

Easy Valet

This unique feature can be activated anytime the alarm is in the

disarmed condition. Easy Valet

is unique because other security systems require the

ignition switch to be "on", but with this system, the ignition can be either "on" or "off".

Page - 9

Page - 11

Safety Disarm/Storm Mode:

and flashing the lights, pressing the large transmitter button will disarm the system only.

The system will not chirp twice or illuminate the parking lights, nor unlock the doors

if the system is configured to also operate the door locks. This safety feature ensures that

the vehicle remain secure should the system require disarming due to being activated from

nuisance or malicious sensory inputs. To remotely unlock the doors if the system is

disarmed while activated, repeat the arm/disarm operation by pressing and releasing the

large transmitter button once, then again. If disarmed from a panic mode, the normal disarm

indications are present, including the unlocking of the doors.

Automatic Rearming:

On occasion people have accidentally disarmed their security

system by playing with the transmitter or by unknowingly transmitting from a purse or

pocket. To prevent accidental disarming, if the Automatic Rearming Feature is utilized, the

system will automatically rearm itself 90 seconds after disarming, unless the ignition switch

is turned "on". If the "Doors Lock With Automatic Rearming" Programmable Feature is

utilized, the doors will also lock when the system automatically rearms. Automatic

Rearming is indicated by a fast flashing LED Status Light. Once the ignition switch is turned

"on", the system will stay in the disarmed condition until you are ready to arm the system

again from the transmitter or from the Last Door Arming Feature. Opening a door will also

cancel Automatic Rearming, although the countdown will resume when the door is shut if

Last Door Arming is on. In this case, while the door is open, the LED Status Light will be

on steady until the door is shut, upon which time it will resume flashing fast. Regardless

of either condition, if the ignition is turned "on", all automatic arming functions will cease.

Whenever the security system is disarmed, simply depress the Easy Valet

two seconds to achieve the Valet Mode, then release. The system will confirm it is in the

Valet Mode with two siren chirps, and the LED Status Light will become constantly

illuminated. The system will hold memory of the Valet Mode condition while the ignition

is "on" or "off". While in the Valet Mode, the transmitters can still operate the Panic feature,

an optional power doorlock interface, or optional trunk release. Additionally, the doors will

lock when the ignition is turned "on" and unlock when turned "off"', if this programmable

feature is being utilized. Easy Valet

Last Door Arming or Automatic Rearming) arming of the system.

Valet Override - Disarming The Security System Without The Transmitter:

In the event the transmitter is lost, damaged, or its batteries become exhausted, the Easy

Valet

Switch and your ignition key may be used to disarm the system:

Step 1: With the system in the armed condition, enter via the driver's door (be aware that

the alarm will activate when the door is opened).

Step 2: Using your key, turn "on" the ignition.

Step 3: Within 10 seconds, press and hold the Easy Valet

instantly.

The Easy Valet

Switch is also part of the programming operations for learning new

transmitter codes and changing programmable features.

While the system is activated, i.e. sounding the siren

Page - 10

Mode prevents active (via transmitter) or passive (via

Switch and the alarm will disarm

Page - 12

Switch for