Audiodesign PAMX3.82 Посібник користувача - Сторінка 6

Переглянути онлайн або завантажити pdf Посібник користувача для Музичний мікшер Audiodesign PAMX3.82. Audiodesign PAMX3.82 8 сторінок. Professional mixer

Друкувати сторінку
PROFESSIONAL MIXER
CONTROL PANEL
The stereo channel(B)
1 L left line input
These are two unbalanced connectors to which the left of a line level device can be
ST LINE 13/14
1
connected, the rated input level is -10dB.
L
Here it is convenient for selecting RCA connector or phone jack.
R
2 R Right line input
L
These are two unbalanced connectors to which the right of a line level device can be
connected, the rated input level is -10dB.
Here it is convenient for selecting RCA connector or phone jack.
-10
3
dB
R
3 -10dB attenuation switch
2
Press this knob, the input signal will be attenuated 10dB, when the input signal level is
too strong.
HI
4
HI :
4
+
This knob control the frequency equalizer at higher frequency point.
- 15
15
MID
Max adjust range：
5
+
- 15
15
LOW
5
:
MID
6
This knob control the frequency equalizer at middle frequency point.
+
- 15
15
Max adjust range:
AUX1
6
LOW:
0
10
AUX2
This knob control the frequency equalizer at lower frequency point.
Max adjust range:
0
10
7
AUX3
7
AUX1,AUX2,AUX3,AUX4:
0
10
These 4
knobs are used for controlling the signal level feed to AUX1~4 bus, these 4 parts are all
AUX4
set in front of the channel fader, so they are not dependent on the fader position.
0
10
8
BAL：
This knob is used for controlling the stereo signal of the channel feed to L/R buses as
some proportion to balance the stereo sound image.
BAL
8
9 SIG,PEAK Indicador:
L
R
These two LED indicators detect the signal level which exists at the end of the
PK
PK
9
channel but in front of the channel fader. SIG LED flashing means the channel is in
SIG
SIG
normal, and PEAK LED will be light at 6dB before clipping to remind that the signal
10
level is too strong to the unit will be overload.
PFL
11
SUB
0
10 CHANNEL FADER:
MAIN
12
This fader controls the output level feed to main bus from the input channel, adjusting the volume
balance between channels. Faders of channels not in use should be pulled down.
-10
-15
-20
10
11 PFL
switch
-30
This switch allows you to monitor the signal of the input channel, the signal is
-50
sampled in front of the channel fader, so it has nothing to do with the fader position.
13/14
12 SUB,MAIN channel output control:
These two switches control if the channel signal will feed to the SUB and MAIN bus
or not separately. The switch should be turned off for unused channels.
PAGE 6
Serie
±
15dB @ 12KHz
±15dB @ 2.5KHz
±15dB @ 80Hz
:
PAMX3
99 preset DSP effect list
01
02
03
04
REVERB HALL
05
06
07
08
09
10
11
REVERB ROOM
12
13
14
15
16
17
REVERB PLATE
18
19
20
21
22
23
AMBIENT
24
25
26
27
28
GATED REVERB
29
30
31
32
33
34
REVERSE REVERB
35
36
37
PROFESSIONAL MIXER
73
60 MS
2.0 S
38
CHORUS MED
74
2.5 S
39
80 MS
75
100 MS
3.0 S
40
VOICE DOUBLER
76
120 MS
4.0 S
41
CHORUS SLOW &ECHO 0.3 S
77
5.0 S
42
140 MS
78
6.0 S
0.1/1.0 S
43
79
8.0 S
ECHO & ROOM
44
0.15/1.5 S
80
FLANGER FAST &ECHO 0.1 S
10.0 S
81
45
0.2/2.0 S
1.0 S
82
0.25/2.5 S
46
1.5 S
FLANGER MED &ECHO 0.2 S
83
0.3/3.0 S
2.0 S
47
ECHO & HALL
84
48
0.35/3.5 S
2.5 S
85
0.4/4.0 S
49
3.0 S
86
FLANGER SLOW&ECHO 0.3 S
0.5/5.0 S
4.0 S
50
87
1.0 S
100 MS
51
1.5 S
88
125 MS
52
TREMOLO FAST
2.0 S
89
53
150 MS
2.5 S
90
200 MS
54
TREMOLO MED
3.0 S
91
250 MS
55
4.0 S
92
56
300 MS
ECHO 50% FB
TREMOLO SLOW
0.5 S
93
350 MS
57
0.7 S
58
400 MS
94
WAH WAH FAST
1.0 S
500 MS
59
95
1.3 S
650 MS
60
96
WAH WAH MED
1.6 S
61
800 MS
97
75 MS
98
62
50 MS
WAH WAH SLOW
100 MS
99
63
100 MS
125 MS
64
150 MS
150 MS
65
200 MS
200 MS
SINGLE DELAY
66
250 MS
300 MS
67
300 MS
75 MS
68
400 MS
100 MS
69
500 MS
125 MS
150 MS
70
200 MS
71
CHORUS FAST &ECHO 0.1 S
300 MS
72
&ROOM 1 S
PAMX3
Serie

EFFECT LIST

&ECHO 0.2 S
&HALL 2 S
&HALL 4 S
&ROOM 1 S
&HALL 2 S
&HALL 4 S
&ROOM 1 S
&HALL 2 S
&HALL 4 S
&ROOM 1 S
&HALL 2 S
&HALL 4 S
PAGE 11