Casio SE-G1 Посібник із швидкого старту

Переглянути онлайн або завантажити pdf Посібник із швидкого старту для Касовий апарат Casio SE-G1. Casio SE-G1 2 сторінки. Australian
Також для Casio SE-G1: Посібник зі швидкого програмування (2 сторінок)

Друкувати сторінку

Quick Start Guide

Electronic Cash Register SE-G1/PCR-T273/SM-T274/SE-S700

Preparations

Note: Please follow the steps described below.

• Unpack the Cash Register and DO NOT plug

the power cord in until sections 1 and 2 have

been completed.

• To prevent losing all your settings and sales

data, we strongly recommend that you set the

memory protection batteries before you use

the cash register and replace them at least

once a year.

1. To set memory protection

batteries

Remove the printer cover by lifting it up.

Remove the take up reel.

Remove the battery compartment cover and

install two new "AA" type batteries in the battery

compartment.

QSG256STP*E3

Replace the battery compartment cover.

Important

• Be sure that the plus (+) and minus (-)

ends of the batteries are facing in the

directions as indicated on the battery

compartment.

• The Cash Register will show an ʽLʼ in the

left hand corner of the display when the

batteries are running low on power. Install

two new batteries when this occurs.

2. To set a paper roll

This Cash Register is fitted with a Thermal Printer -

only Thermal paper till 58 mm Rolls can be used.

Open the platen arm by lifting it up.

Hold the paper roll so that the end of the paper

comes out from the bottom of the roll and place

it behind the printer.

Place the end of the paper over the printer.

For programming assistance Please visit http://casio4business.com/sa_index.html

Close the platen arm slowly until it locks

securely.

Note: Never touch the printer's thermal head

and the platen. Avoid the thermal paper

from heat, humidity or direct sunlight.

Important

• If the thermal paper roll is not properly

installed, you will not be able to use the

cash register. The E10 error code will be

displayed to indicate that the printer is

not working.

3. To turn the cash register

Insert a Mode key that comes with the cash

position.

Plug in the power cord into an AC outlet.

For Technical support Please call TOLL FREE 1-800-435-7732

4. To set language, date and

time

As soon as you plug in the power cord, the

printer prints instructions for selecting lan-

guage. If you wish to select English, press

keys. For selecting Spanish, press

keys.

The printer then prints the instructions for

setting date and time and the first digit of the

display flashes. Enter the date in order of

month, day, and year. For example, 012114

for January 21, 2014. The display changes for

setting time. Enter the present hour and minute

in 24 -hour system.

Note: At this point the till will automatically turn

off, as the setup procedure has been

completed. Please note that the key is

still in the OFF position.

Important

• Once the time has been entered, the Cash

showing the date and time at the bottom -

check that this is correct.

5. To set tax rate

Turn the Mode switch to PGM position.

Enter

then press

key for setting the

Enter

then press

to set the

??XB

Referring the tax table on page E-12 of the

User's Manual, enter the tax table number for

Tax table 1 then press

key.

For example, to set Alabama 4% state and local

tax, enter ?Z?Zp.

Note: If there is no tax table falling under your

requirement, please see "To set tax

tables and rounding system" on page

E-41 of the User's Manual to set tax

rates manually.

If necessary, repeat the step 4 for Tax table 2.

Press

key to complete the settings.

Note: By default, department 02 is pro-

grammed as taxable status 1 and the

rest of departments are set as non-

taxable status.

If you wish to change the taxable

statuses of departments, please see

"To change taxable statuses of depart-

ments" on page E-14 of the User's

Manual.

To set a journal paper

By default, your cash register issues receipts. You

can change it to print journals by changing the

setting.

Turn the Mode switch to PGM position. "P"

appears on the display.

Press

to set the cash register in

program mode.

Press

to set the register in "Jounal"

mode.

Remove the printer cover by lifting up.

Turn the Mode switch to REG and press

key so that the paper is fed about 15 cm.

Remove the left plate of the take up reel and

insert the edge of the paper between the gap of

the shaft.

Turn the reel a few turns so that it holds the

paper securely then replace the left plate.

Place the take up reel behind the printer and

press

key to reduce a slack of the paper.

Replace the printer cover.

Note: If you wish to restore the register to

"Receipt" mode, press

in step 3.

The default setting of your cash register

is to print receipts. If you wish to use it

to print journals, please see the above.