Belden HIRSCHMANN RS2-3TX/2FX EEC Опис та інструкція з експлуатації - Сторінка 4

Переглянути онлайн або завантажити pdf Опис та інструкція з експлуатації для Мережевий маршрутизатор Belden HIRSCHMANN RS2-3TX/2FX EEC. Belden HIRSCHMANN RS2-3TX/2FX EEC 10 сторінок. Industrial ethernet rail switch 2

Друкувати сторінку

ATEX Directive 94/9/EC –

Special conditions for safe use

Relevant for RS2-xTX/xFX EEC devices

when operating in explosive gas atmosphe-

res according to ATEX Directive 94/9/EC, the

following applies:

List of Standards:

- EN 60079-0:2009

- EN60079-15:2010

Certificate No.: DEKRA 13ATEX0013 X

Make sure that the device has the follo-

wing label:

II 3G Ex nA IIC T4 Gc DEKRA

13ATEX0013 X

Ambient rating and temperature code:

Ta: -40 °C ... +60 °C

The modules shall be installed in a sui-

table enclosure in accordance with EN

60079-15 providing a degree of protection

of at least IP54 according to EN 60529,

taking into account the environmental con-

ditions under which the equipment will be

used.

When the temperature under rated con-

ditions exceeds 70 °C at the cable or conduit

entry point, or 80 °C at the branching point

of the conductors, the temperature specifi-

cation of the selected cable and cable

entries shall be in compliance with the

actual measured temperature values.

Provisions shall be made to prevent the

rated voltage from being exceeded by tran-

sient disturbances of more than 119 V.

Connectors shall be connected or dis-

connected exclusively in dead-voltage state.

DIP switches shall be switched exclusi-

vely in dead-voltage state.

Safety Guidelines Environment

Warning!

The device may only be operated in

the listed surrounding air tempera-

ture and at the listed relative air

humidity (non condensing).

The installation location is to be selec-

ted so as to ensure compliance with the cli-

matic limits listed in the Technical Data.

To be used in an up to Pollution Degree

2 environment only (IEC 60664-1).

Staff qualification

requirements

Note: Qualified personnel, as understood

in this manual and in the warning signs, are

persons who are familiar with the setup,

assembly, startup, and operation of this

product and are appropriately qualified for

their job. This includes, for example, those

persons who have been:

– trained or directed or authorized to

switch on and off, to ground and to label

power circuits and devices or systems in

accordance with current safety enginee-

ring standards

– trained or directed in the care and use of

appropriate safety equipment in accor-

dance with the current standards of safety

engineering

– trained in providing first aid.

General Safety Instructions

This device is electrically operated.

Adhere strictly to the safety requirements

relating to voltages applied to the device as

described in the operating instructions!

Warning!

Failure to observe the information

given in the warnings could result in

serious injury and/or major damage.

Only personnel that have received

appropriate training should operate

this device or work in its immediate

vicinity. The personnel must be fully

familiar with all of the warnings and

maintenance measures in these

operating instructions.

Correct transport, storage, and

assembly as well as careful operati-

on and maintenance are essential in

ensuring safe and reliable operation

of this device.

Use only undamaged parts!

These products are only to be used in

the manner indicated in this version of the

"Description and Operating Instructions".

Particular attention is to be paid to all

warnings and items of information relating

to safety.

Warning!

Any work that may have to be per-

formed on the electrical installation

should be performed by fully quali-

fied technicians only.

Warning!

LED- or LASER components accor-

ding to IEC 60825-1:

CLASS 1 LASER PRODUCT.

LIGHT EMITTING DIODE - CLASS 1

LED PRODUCT.

Based specifications and

standards:

The devices fulfil the following specificati-

ons and standards:

– EN 61000-6-2 Basic standard –

interference resistance in industry.

– EN 55022 – Interference characteristics for

IT systems.

– EN 60950 – Security in IT systems.

– EN 61131 – Programmable Logic Control-

lers.

– CFR-47 Part 15 – Code of Federal Regulati-

ons.

– UL 508 – Underwriters Laboratories Inc.

Safety for Industrial Control Equipment.

– ISA 12.12.01 – Nonincendive Electrical

Equipment for Use in Class I and II, Divisi-

on 2 and Class III, Divisions 1 and 2 Hazar-

dous (Classified) Locations.

– UL 60950 – Safety for Information

Technology Equipment.

– Germanischer Lloyd – rules for classifica-

tion and construction VI-7-3 part 1.

Certified devices are marked with a

certification identifier.

Notes on CE

identification

The devices comply with the regula-

tions of the following European

directives:

2004/108/EC (EMV)

Directive of the European Parlia-

ment and of the Council on the

approximation of the laws of the

Member States relating to electro-

magnetic compatibility.

2011/65/EU (RoHS)

Directive of the European Parlia-

ment and of the Council on the

restriction of the use of certain

hazardous substances in electrical

and electronic equipment.

The EU declaration of conformity is

kept available for the responsible

authorities in accordance with the

above-mentioned EU directives at:

Hirschmann

Automation and Control GmbH

Stuttgarter Straße 45-51

D-72654 Neckartenzlingen

Telephone: +49 (0)1805 14-1538

The product can be used in the indu-

strial sphere.

– Interference immunity:

EN 61000-6-2

– Radio interference level:

EN 55022 Class A

Warning!

This is a Class A device. This equip-

ment may cause radio interference if

used in a residential area; in this

case it is the operator s responsibili-

ty to take appropriate measures.

The precondition for compliance

with EMC limit values is strict adhe-

rence to the construction guidelines

specified in this description and

operating instructions.

FCC Note:

This equipment has been tested and found

to comply with the limits for a Class A digi-

tal device, persuant to part 15 of the FCC

Rules. These limits are designed to provide

reasonable protection against harmful inter-

ference when the equipment is operated in

a commercial environment. This equipment

generates, uses, and can radiate radio fre-

quency energy and, if not installed and

used in accordance with the instruction

manual, may cause harmful interference to

radio communications. Operation of this

equipment in a residential area is likely to

cause harmful interference in which case

the user will be required to correct the inter-

ference at his own expense.

Recycling Note:

After its use, this product has to be

processed as electronic scrap and

disposed of according to the prevai-

ling waste disposal regulations of

your community / district / country /

state.