Consort SLPBWIFI Посібник зі встановлення та керування - Сторінка 3

Переглянути онлайн або завантажити pdf Посібник зі встановлення та керування для Контролер Consort SLPBWIFI. Consort SLPBWIFI 8 сторінок. Wireless controller

Друкувати сторінку

2. Using the push button

Before connecting to WIFI and APP:

After the pairing with the heaters has been complet-

ed (see paragraph 3 for more details) The push but-

ton can be used to activate and deactivate heat-

ing. Push button briefly to activate heating, push

again to deactivate heating. Temperature control

isn't available.

After connecting to WIFI and APP:

After the pairing with the heaters, the WIFI and APP

have been completed. (see paragraph 3 & 4 for

more details) The function of the push button now

changes. The push button can be now used to tog-

gle between the BOOST MODE and mode selected

by the APP. Press the button briefly to set controller to

BOOST mode. Double press the button to return to

the previous mode.

The BOOST mode is time limited to 15 minutes. After

15 minutes, the heating will revert to the previous op-

erating mode set on the APP.

3. Pairing with heaters

In order to pair controller with heaters:

· Ensure the controller is powered and has been

powered for more than 10 seconds.

· Power up the heater.

· Within 20 seconds, press and hold the button on the

controller until the segments flash yellow.

Alternatively select 'Send pairing signal' in the app

settings menu.

· After the pairing is finished, the light segments will

change to green.

· If the pairing was successful, the heater should emit

heat. It can take up to 4 seconds.

· Depending on the operating mode, the appliance

may switch off after 4 seconds.

· The heater is now ready to be used.

4. Pairing to the Consort Connect app

The controller is only compatible

with a 2.4GHz WIFI network.

All internet routers support the 2.4GHz band, as it is

an older standard and has maximum device com-

patibility. Routers also support 5GHz WIFI and are of-

ten set up to hide which frequency band is being

used, combine both bands into a single network

name, and assign the band automatically. A mobile

phone could be automatically connected to the

5GHz network, and this will cause pairing issues.

Routers usually have a setting that gives each band

to have a different network name, which is configu-

rable through the router's web interface. This allows

the phone to unambiguously select the 2.4GHz net-

work. For full pairing instructions, see section 9.

Before pairing the App must be installed on your

smart phone. The app is compatible with IOS and

Android Smartphones. Go to the app store or play

store and search :

Consort Connect

When the app asks for the WIFI make sure that the

WIFI network and password are entered correctly –

the app usually selects the right network, but you

need to enter the password. Until you successfully

pair a device to a network it does not remember the

password, and if the password is entered incorrectly

it doesn't specifically tell you that this is the problem.

Pairing the heater to the Consort Connect app.

Ensure the smartphone or tablet is connected

to 2.4GHz WIFI network and the Bluetooth is

enabled.

Within 10 seconds after powering the control-

ler, press and hold the button until the green

lights start flashing.

The Blue indicator should also be flashing.

Select the + symbol in the top right corner of

the Consort Connect app

Select "Heater (BLE)"

The app will ask you to confirm the indicator is

blinking rapidly.

If the blue indicator is flashing rapidly, tick the

box and click ' Next '.

The app should show that one device has

been found. Select the + symbol next to this

device.

Enter the WIFI password on the app.

10.

The heater will begin to pair to the app. This

can take up to 60 seconds.

11.

Once pairing is successful, the + symbol will be

replaced with a tick.

12.

Select ' Next ' and the app should display

'Added successfully'. The controller is now

paired and ready to be used with the app.

A solid blue light on the controller means the con-

troller is connected to the internet.

5. How to control the product using the app

When you open the Consort Connect app, select

the product you would like to control. This will bring

you to the main control page where you can

change the operating mode and temperature. The

dial in the middle of the screen is used to adjust the

temperature. The icons on the top of the screen

are used to change the operating mode.