Datalogic Heron D130 Короткий довідник - Сторінка 2

Переглянути онлайн або завантажити pdf Короткий довідник для Зчитувач штрих-коду Datalogic Heron D130. Datalogic Heron D130 3 сторінки.
Також для Datalogic Heron D130: Короткий довідник (2 сторінок)

Друкувати сторінку

DEFAULT VALUES

USB-KBD DEFAULT SETTINGS

USA keyboard, FIFO enabled, inter-character and inter-code delays disabled,

control character emulation = ctrl+shift+key.

: code identifier disabled, no field adjustment, code length not

DATA FORMAT

transmitted, no header, terminator = ENTER, character replacement disabled.

RS232 Standard DEFAULT SETTINGS

9600 baud, no parity, 8 data bits, 1 stop bit, no handshaking, delay disabled, rx

timeout 5 sec., ack/nack disabled, FIFO enabled, serial trigger lock disabled.

: code identifier disabled, no field adjustment, code length not

DATA FORMAT

transmitted, no header, terminator = CR-LF, character replacement disabled.

WEDGE DEFAULT SETTINGS

USA keyboard, caps lock off, caps lock auto-recognition enabled, num lock

unchanged, inter-character and inter-code delays disabled, control character

emulation = ctrl+shift+key.

: code identifier disabled, no field adjustment, code length not

DATA FORMAT

transmitted, no header, terminator = ENTER, character replacement disable.

PEN DEFAULT SETTINGS

interpret mode, conversion to code 39 disabled, output level normal, idle level

normal, minimum output pulse 600 µs, overflow medium, inter-block delay disabled.

CODE SELECTION

Enabled codes

•

EAN 8/EAN 13 / UPC A/UPC E without ADD ON

check digit transmitted, no conversions

•

Interleaved 2/5

check digit control and transmission, variable length code; 4-99 characters

•

Standard Code 39

no check digit control, variable length code; 1-99 characters

•

Code 128

variable length code; 1-99 characters

Disabled codes

EAN 128, ISBT128, Code 93, Codabar, pharmaceutical codes, MSI,

Plessey, Telepen, Delta IBM, Code 11, Code 16K, Code 49, RSS Codes

TECHNICAL FEATURES

Heron™ D130

Electrical Features

Power Supply

RS-232 interface

5 Vdc ± 5%

Consumption:

Maximum

180 mA @ 5 Vdc

Operating

155 mA @ 5 Vdc

Sleep mode/USB Suspend

< 2,5 mA @ 5 Vdc

Max. Scan Rate

256 scans/sec

Reading Indicators

LED, Good Read Spot, Beeper

Optical Features

Sensor

CCD solid state (2048 pixels)

Illuminator

LED array

Wavelength

630 ~ 670 nm

Max. LED Output Power

0.31 mW

LED Safety Class

Class 1 EN 60825-1

Reading Field

2 ~ 27 cm (20 mils)

Max. Resolution

0.10 mm (4 mils)

PCS (Datalogic Test Chart)

min. 15%

Environmental Features

Working Temperature

0 °C to + 55 °C (+32° to +131 °F)

Storage Temperature

-20 °C to + 70 °C (-4° to +158 °F)

Humidity

90% non condensing

IEC 68-2-32 Test ED

Drop Resistance

1.8 m (5.9 ft)

ESD Protection

16 KV

Protection Class

IP30

Mechanical Features

Weight (without cable)

about 160 g (5.6 oz)

Cable Length

2 m (6 ft 6 in)

RESTORE DEFAULT

Ì$+$*oÎ

To change the defaults refer to the HHD II Software Configuration Manual, or to the

Datalogic Aladdin Configuration program, both downloadable from the website.

INTERFACE SELECTION

Select one of the interface codes according to your application.

USB INTERFACE SELECTION

USB-KBD

Ì$+UA03$-:Î

USB-KBD - ALT-mode

Ì$+UA04$-@Î

USB-COM *

Ì$+UA02$-4Î

USB-IBM-Hand Held

Ì$+UA01$-.Î

* When configuring USB-COM, the relevant files and drivers must be installed from

the USB Device Installation software, which can be downloaded from the web

site http://www.datalogic.com.

PEN EMULATION INTERFACE SELECTION

PEN

Ì$+CP6$-BÎ

RS-232 INTERFACE SELECTION

RS-232 Standard

Ì$+CP0$-$Î

Nixdorf Mode A

Ì$+CM2EC0$->Î

Fujitsu

Ì$+CM1$-ÈÎ

ICL Mode

Ì$+CM0$-ÃÎ

WEDGE INTERFACE SELECTION

Wedge IBM AT or PS/2 PCs

Ì$+CP500$-aÎ

PC Notebook

Ì$+CP505$-ÈÎ

PC Notebook - ALT mode

Ì$+CP508$-2Î

IBM AT - ALT mode

Ì$+CP507$-+Î

Many other interfaces are supported and can be selected from the HHD II Software

Configuration Manual available online at datalogic.com. Other supported interfaces:

USB: USB-IBM-Table Top; USB-KBD-APPLE

WEDGE: IBM XT; IBM SURE1; IBM Terminal 3153; IBM Terminals 31xx, 32xx,

34xx, 37xx; VT220 style Keyboards; Digital Terminal VT2xx/VT3xx/VT4xx; APPLE

ADB Bus

KEYBOARD NATIONALITY

USB-KBD and Wedge users should select one of the following wedge keyboard

nationality codes according to your keyboard.

Belge

Ì$+FJ7$-8Î

Deutsch

Ì$+FJ3$-$Î

English

Ì$+FJ4$-)Î

Español

Ì$+FJ6$-3Î

Français

Ì$+FJ2$-ÊÎ

Italiano

Ì$+FJ1$-ÅÎ

Japanese

Ì$+FJ8$-=Î

Svenskt

Ì$+FJ5$-.Î

USA (Default)

Ì$+FJ0$-|Î

DATA FORMAT TERMINATORS

For your convenience, some common Terminators are given below. For other

Header/Terminator selections, Data Format and Advanced Data Format

parameters, see the HHD II Software Configuration Manual.

CR-LF

Ì$+EA120D0A$-ÃÎ

Enter

Ì$+EA1183$-0Î

Tab

Ì$+EA1184$-8Î

None

Ì$+EA10$-dÎ

OPERATING TEST

Read the TEST code below.

Code 128

USING HERON™ SERIES READERS

Heron™ readers automatically scan barcodes at a distance. Simply aim and pull

the trigger. Code scanning is performed along the center of the light bar emitted

from the reading window. This bar must cover the entire code.

Successful scanning is obtained by tilting the scanner with respect to the barcode

to avoid direct reflections, which impair the reading performance (see the figure

above).

Successful reading is signaled by an audible tone plus a good-read green spot.

Once the reader is correctly inserted into the stand, it is immediately ready to

automatically read any code present in its reading area without pressing the trigger.

Furthermore, a green aiming light is continuously emitted to facilitate the

positioning of the barcode to be read (see the figure above).

To guarantee single code reading, same code consecutive reading requires the

code to be removed from the reading area (no decoding) before the reader will

accept the same code.

STAND INSTALLATION

The stand can be mounted by using self-tapping screws, double sided adhesive

strips or rubber feet:

Mount the stand directly to the surface using the self-tapping screws;

Carefully clean the bottom surface of the stand and the table surface.

Remove the protective plastic from one side of the adhesive strips and stick

them on the stand bottom. Then, remove the plastic from the other side of the

strips and affix the stand to the table;

Carefully clean the bottom surface of the stand, remove the protective film

from the rubber feet and stick them in the corresponding housing on the

bottom surface. It is also possible to affix an optional metal plate.

INSERTION INTO STAND

Pair the reader to the stand, taking care to insert the handle into the stand clip (see

figure above). Correct insertion will be signaled by a beep; then, the reader will be

ready to read barcodes.