Datalogic ELF Посібник - Сторінка 2

Переглянути онлайн або завантажити pdf Посібник для КПК Datalogic ELF. Datalogic ELF 2 сторінки. Four slot dock
Також для Datalogic ELF: Посібник із швидкого старту (2 сторінок), Посібник із швидкого старту (2 сторінок), Посібник із швидкого старту (2 сторінок), Посібник із швидкого старту (2 сторінок), Посібник із швидкого старту (2 сторінок)

Друкувати сторінку

Daisychaining Ethernet Connection

To connect several cradles to an Ethernet network, the Ethernet

cradles may be daisychained. It is recommended not to connect

more than 4 cradles in order to maintain the optimal baud rate.

Connect the first Ethernet cradle to the Ethernet Switch. Connect the

additional cradles as shown in Figure 7.

Figure 7 - Daisychaining Ethernet Connection

Key:

A) Power supply without power cord, supplied with the 4SD and

country specific power cord

B) Ethernet hub

C) UTP CAT 5E cable (recommended use)

D) Ethernet Port 1

E) Ethernet Port 2

This is a Class A product. In a domestic environment

this product may cause radio interference in which

case the user may be required to take adequate

measures.

WARNING

Do not use the cradle in a PoE network, i.e. in a

network with PSE able to supply power: there is the

risk to compromise, in irreversible way, the

functionality of the cradle.

WARNING

DOCK DOCK CONTACTS CLEANING PROCEDURE

All exterior metal contacts/connectors exposed to spills, dirt or debris

accumulation require periodic cleaning to ensure best performance

during charging and data transmission.

Use a soft, lint-free dry cloth or lens tissue to clean the product

(contacts and plastics). An antistatic cloth is preferable but you can

also use a cotton cloth. Avoid wool, synthetic cloths or other

materials that can cause electrostatic discharges.

If the contacts are very dirty, clean them with a soft cloth moistened

with a diluted non-aggressive cleaning solution or a diluted isopropyl

alcohol solution (20% maximum). A cotton swab may be used only

on hard-to-reach contacts.

Clean the contacts when you see traces of dirt or when you

experience solid connection issues between the terminal and its

dock (device not charging or intermittent communications). It is

however suggested to clean the contacts every 6 months (more

often if the environment is dusty).

If the plastic areas are very dirty use only a cloth dampened with

water.

Do not use abrasive or aggressive cleaning agents

or abrasive pads to clean electric contacts, scan

windows or plastics.

CAUTION

Cleaning the Dock Contacts

Remove the power cable before cleaning the contacts.

Use a soft dry cloth as suggested above. If the product is very

dirty, moisten the cloth in a non-aggressive cleaning solution or

diluted isopropyl alcohol solution (20% maximum).

Gently rub the cloth back and forth ONLY along the contacts,

following the directions indicated by the red arrows. Use care

not to leave any cloth residue.

Use a dry cloth to remove any dirt near the contacts area and to

clean the plastic parts. If the plastic parts of the equipment are

very dirty, slightly dampen the cloth with only water.

Repeat steps 2, 3 and 4 using a clean dry cloth.

Allow the cleaning solution to fully evaporate before powering

up the product.

Cleaning the Dock Auxiliary Battery Contacts

Remove the power cable and the Ethernet module before

cleaning the contacts.

Use a soft dry cloth as suggested above. If the product is very

dirty, moisten the cloth in a non-aggressive cleaning solution or

diluted isopropyl alcohol solution (20% maximum).

Gently rub the cloth back and forth ONLY along the contacts,

following the directions indicated by the red arrows. Use care

not to leave any cloth residue.

Use a dry cloth to remove any dirt near the contacts area and to

clean the plastic parts. If the plastic parts of the equipment are

very dirty, slightly dampen the cloth with only water.

Repeat steps 2, 3 and 4 using a clean dry cloth.

Allow the cleaning solution to fully evaporate before powering

up the product.

TECHNICAL FEATURES

Electrical Features

Power supply *

12 VDC ± 5% @ 5A

Consumption

Max 5 A

Spare slot charge time

Elf Std Battery

4h 30

Falcon X3/Elf High

6h 30 (with terminal inserted)

Cap Battery

5h (when terminal is not inserted)

Communication Features

Interface

Ethernet **

Baud Rate

10/100BASE-T

Physical Features

Dimensions

445 x 135 x 105 mm

17.5 x 5,3 x 4.2 in

Weight

(without

1250 g / 44.1 oz

connection cables)

Indicators

Green power-on LED

Bicolored battery charge status LED

Environmental Features

Working temperature***

-10° to +50°C / 14° to 122°F ***

Storage temperature

-20° to +70°C / -4° to 158°F

Humidity

95% without condensation

Electrostatic discharge

4 KV contact / 8 KV air

EN 61000-4-2

Use only DL approved power adapters.

** Available in the Ethernet Four Slot Dock only

*** When inserted in the spare slot, standard batteries must be charged at

a temperature ranging from 0° to 40 °C.

When inserted in the spare slots, high capacity batteries must be

charged at a temperature ranging from 0° to 35 °C.

At higher values the charging may slow down.

FCC COMPLIANCE

This equipment has been tested and found to comply with the

limits for a Class A digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is

operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual,

may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause

harmful interference in which case the user will be required to

correct the interference at his own expense.

Modifications or changes to this equipment without the expressed

written approval of Datalogic could void the authority to use the

equipment.

This device complies with PART 15 of the FCC Rules. Operation

is subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any

interference received, including interference which may cause

undesired operation.

Datalogic and the Datalogic logo are registered trademarks of Datalogic

S.p.A. in many countries, including the U.S.A. and the E.U. Elf and

Falcon are trademarks of Datalogic S.p.A. and/or its affiliates.

All other brand and product names may be trademarks of their respective

owners.