Dustless 16003 Посібник користувача - Сторінка 5

Переглянути онлайн або завантажити pdf Посібник користувача для Пилосос Dustless 16003. Dustless 16003 9 сторінок. 16 gallon
Також для Dustless 16003: Посібник користувача (4 сторінок)

Друкувати сторінку

Wet Pickup:

Dry waste should be emptied from tank

and intermediate cover but filters can remain

in place.

Should filters become wet, during use, dry both

filters thoroughly before continued use, consult

the trouble shooting guide (Filters get wet).

fter Wet Pickup:

Unscrew drain

cap from bottom

of tank. This

drain is regulated so that

a floor drain can be used conveniently.

The liquid can be regulated from a drip to

a full flow.

The suction hose can be put in the drain cap to

drain liquid up to 12 feet away.

Rinse inside of tank thoroughly with clean water

particularly if spills or other substances other

than water have been

picked up. Wipe inside of tank dry. Screw drain

cap back on tightly so it is ready for use again.

utomatic Wet Shut-off:

When the tank is full of liquid, the automatic

shut-off mechanism will shut off cleaner pick-up.

When this happens, the motor sound will

become noticeably higher in pitch. Turn cleaner

off and empty tank to continue use.

Storage:

Disconnect cleaner from electrical outlet. Empty

tank. Rinse inside of tank thoroughly with clean

water particularly if spills or other liquid sub-

stances other than plain water have been picked

up. Wipe inside of tank dry. If tank is stored

with liquid left inside, the moisture may cause

damage to the motor and its internal parts.

Wands and cleaning accessories as well as hose

store right on the accessory tray. Wands store on

each of the back leg grooves provided.

Lubrication:

The motor is equipped with bearings which con-

tain sufficient lubrication for the life of the motor.

The addition of lubricant could cause damage.

Do not add lubricant to motor bearings.

If you have a problem:

This appliance was inspected thoroughly and

was in good operating condition when it was

shipped from the factory. If a minor problem

occurs, it usually can be solved quite easily

when the cause is found. Therefore, this Trouble

Shooting Guide is provided for you convenience.

ToolSync

Operation

o not plug

Electric Tool

Start Module

into the vacuum.

ToolSync Operation:

When the switch is in the I position,

the vacuum will turn on but no power

will be applied to the vacuum ToolSync

outlet. When the switch is in the II

position, power will be applied to the

ToolSync outlet on the vacuum. When

the portable electric tool is activated,

the vacuum will turn on and run until

the tool is turned off, then remain

running for about 6 seconds to clear

the hose. If the portable electric tool

being used is rated 6-8 amps, the

vacuum will reduce power to the

vacuum to keep the total current to the

tool and vacuum below 12 amps. The

tool plugged into the vacuum will

always receive full power. If a large

tool is attached to the vacuum outlet,

there may not be enough available

current to supply the vacuum and the

Wireless ToolSync

Operation

vacuum motor will shut off. If this

occurs, a remote/wireless electric

start module will need to be used.

Some portable electric tools rated

less than 1 amp may not trigger the

automatic mechanism. When these

low amperage tools come into contact

with the work surface, they often

draw enough current to activate the

automatic start. When the vacuum is

started with an attached tool, and the

tool is turned immediately off (within

1-2 seconds), this will allow the

vacuum to remain running in a

"Clean-up mode". To clear "Clean-up

mode", simply turn the tool on for

more than 1-2 seconds, or turn the

vacuum to the off position. "Clean-up

mode" only works with a device

plugged into the vacuum outlet.