CBC ZC-D2550NHA Інструкція з експлуатації - Сторінка 2

Переглянути онлайн або завантажити pdf Інструкція з експлуатації для Аксесуари для фотоапаратів CBC ZC-D2550NHA. CBC ZC-D2550NHA 5 сторінок. Zc-oh2 tamper-resistant indoor/outdoor housing

Друкувати сторінку

MPORTANT

Installation should be performed by a qualified service person and conform

to all local codes.

ESCRIPTION

Model ZC-OH2 is a tamper resistant indoor or outdoor housing which is

designed to accommodate all CBC ZC series minidome cameras. This

housing will accept the following cameras:

Model ZC-D1024EHA

Hi-Res B/W Camera with 2-4mm A/I varifocal

Model ZC-D1036EHA

Hi-Res B/W Camera with 3-6mm A/I varifocal

Model ZC-D1049EHA

Hi-Res B/W Camera with 4-9mm A/I varifocal

Model ZC-D2550EHA

Hi-Res B/W Camera with 5-50mm A/I varifocal

Model ZC-D1024NHA

Hi-Res Color Camera with 2-4mm A/I varifocal

Model ZC-D1036NHA

Hi-Res Color Camera with 3-6mm A/I varifocal

Model ZC-D1049NHA

Hi-Res Color Camera with 4-9mm A/I varifocal

Model ZC-D2550NHA

Hi-Res Color Camera with 5-50mm A/I varifocal

AJOR

EATURES

•

Polycarbonate dome with rugged cast aluminum housing withstands the

blow from a 10 pound sledgehammer

•

O-Ring Sealed housing is completely air-tight and water-tight (when

properly installed) and is suitable for virtually any weather condition

•

Quick and easy installation utilizing 8 different dome camera options

•

Housing mounts directly to any wall, ceiling or 4S Electrical box

•

Interchangeable dome with tinted, gold and chrome options

NSTALLATION

1) Standard Housing Installation

a) Caution: Do Not Remove Screws. Loosen the 3 set screws

from the dome base using the supplied allen key and remove the

dome cover. the O-Ring makes a tight seal, so a thin-bladed screw-

driver may be needed to separate the dome cover from the housing

base.

b) Remove the rubber plugs from the mounting holes inside the base.

Remove only those plugs for the mounting holes that will be used.

c) Using a minimum 7/32" drill bit, drill the cable feed hole and feed the

video/power cable through the mounting surface.

d) Holding the dome against the mounting surface, mark and drill the 4

mounting holes. Fasten the base to the mounting surface using the

supplied #8 Phillips screws, rubber washers and plastic anchors. Be

sure to re-install the rubber plugs into any unused mounting holes.

(Depending on the mounting surface, other hardware may be

needed.)

Note: (If using other mounting hardware)

To prevent damage from leakage, apply silicone sealant

around the inside of the 4 mounting holes before inserting

screws or bolts.

2) Optional Conduit Base Installation (Model ZC-CB2)

a) Install optional conduit base using supplied screws and anchors or

other hardware. Apply a bead of silicone sealant between the base

and mounting surface.

b) Route conduit to base and inset into conduit hole. Lock down the

conduit end with allen head set screw.

c) Feed the power/video cable from the housing base to the loose

wires from the conduit. It may be necessary to shorten the

power/video cable so that all of the spliced connections fit within the

center of the conduit base.

e) Making sure all the connections are tucked into the center of the

conduit base, install the housing base to the conduit base using the

supplied 4 machine screws. Apply a bead of silicone sealant between

the housing base and conduit base.