Datalogic Four Slot Dock Посібник - Сторінка 2
Переглянути онлайн або завантажити pdf Посібник для Док-станція Datalogic Four Slot Dock. Datalogic Four Slot Dock 2 сторінки. For skorpio x3 mobile computer
Друкувати сторінку
ETHERNET CONNECTION
The Ethernet cradle drivers are pre-installed on the Skorpio X3 and
initiate automatically when the terminal is placed in a properly connected
Four Slot Dock Ethernet.
When the mobile computer is inserted into the Four Slot Dock Ethernet,
the connectivity icon on the taskbar indicates that the mobile computer is
connected to a network.
The maximum bandwidth capacity for each Mobile
Computer is 12Mbps.
NOTE
The yellow Link LED blinks to indicate activity, or stays lit to indicate that
a link is established. When it is not lit it indicates that there is no link.
Connections should always be made with power OFF!
CAUTION
How to connect
Connect the Ethernet cradle (Ethernet port 1 - E) to an Ethernet hub or to a
port on the host device. Connect the Ethernet cradle (power port - F) to the
power supply.
A
F
E
B
C
Figure 6 - Ethernet Connection
Key:
A)
Ethernet 4 Slot Dock
B)
Power supply without power cord, supplied with the 4SD and
country specific power cord
C)
UTP CAT 5E cable (recommended use)
D)
Ethernet hub
E)
Ethernet port 1
F)
Power port
Available in the Ethernet Four Slot Dock only
Daisychaining Ethernet Connection
To connect several cradles to an Ethernet network, the Ethernet cradles may
be daisychained. It is recommended not to connect more than 4 cradles in
order to maintain the optimal baud rate.
To daisychain the cradles:
1.
Connect the first Ethernet cradle to the power supply and to the Ethernet
Switch as shown in Figure 6.
2.
Connect the second Ethernet cradle to the power supply.
3.
Connect the daisychain Ethernet cable (either straight or twisted cable
can be used) between the Ethernet Port 2 of the first cradle and the
Ethernet Port 1 of the second cradle.
4.
Connect additional cradles as shown in Figure 6.
A
A
Figure 7 - Daisychaining Ethernet Connection
Key:
A)
Power supply without power cord, supplied with the 4SD and
country specific power cord
B)
Ethernet hub
D
C)
UTP CAT 5E cable (recommended use)
D)
Ethernet Port 1
E)
Ethernet Port 2
This is a Class A product. In a domestic environment this
product may cause radio interference in which case the
user may be required to take adequate measures.
WARNING
TECHNICAL FEATURES
Electrical Features
Power supply *
Consumption
Spare slot charge time
Communication Features
Interface
Baud Rate
Physical Features
Dimensions
Weight (without
connection cables)
Indicators
B
C
Environmental Features
Working temperature***
Storage temperature
Humidity
C
Electrostatic discharge
EN 61000-4-2
*
Use only DL approved power adapters.
**
Available in the Ethernet Four Slot Dock only
D
E
*** Skorpio X3 (including spare battery) should be charged at an ambient
temperature between 0 - 35º C to achieve the maximum charging rate.
Never charge the main device or spare batteries in a closed space
(cabinet) where excessive heat can build up.
FCC COMPLIANCE
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
Modifications or changes to this equipment without the expressed written
approval of Datalogic could void the authority to use the equipment.
This device complies with PART 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference which may cause undesired operation.
12 VDC ± 5% @ 5A
Max 5 A
Skorpio X3 Std
4h 30
Battery
Skorpio X3 High
6h 30 (with terminal inserted)
Cap Battery
5h (when terminal is not inserted)
Ethernet **
10/100BASE-T
445 x 135 x 105 mm
17.5 x 5,3 x 4.2 in
1250 g / 44.1 oz
Green power-on LED
Bicolored battery charge status LED
-10° to +50°C / 14° to 122°F ***
-20° to +70°C / -4° to 158°F
95% without condensation
4 KV contact / 8 KV air