Datamax MICROFLASH 4T Посібник

Переглянути онлайн або завантажити pdf Посібник для Виробник етикеток Datamax MICROFLASH 4T. Datamax MICROFLASH 4T 2 сторінки. External charger swivel lock
Також для Datamax MICROFLASH 4T: Посібник із швидкого старту (2 сторінок)

Друкувати сторінку

MF4 External Charger Swivel Lock

(220226-003)

Swivel

Foot

Lock

Adapter

Cradle

Figure 1

Parts List

(1) MF4 External Swivel Lock Depot Charger

(1) High capacity AC adapter

(1) Grounded AC power cord

(7) #10 x 1¼" wood screws (not shown)

(7) #10 flat washers (not shown)

#8 - #10 toggle bolts [not included; length to be

determined by the user

Note: Use #10 x 1¼" wood screws to mount the

charging dock to wood surfaces only. The

#10 x 1¼" wood screws cannot be used to mount

the depot charger to any other type of surface.

Use #8 - #10 toggle bolts if you are mounting the

depot charger to drywall.

Guidelines

General Guidelines

•

The MF4 Depot Charger is designed to be used as a

desktop or wall mounted unit.

•

Keep the charging dock in a cool, dry place, away from

direct sunlight, high temperature, and moisture.

•

The depot charger takes approximately 3-4 hours to

charge each printer. If multiple printers are attached, the

charge time remains at approximately 3-4 hours per

printer; however, charge times may vary.

•

The depot charger is not recommended for use with the

MF2t Smart CardReader (SCR) or MF4t Smart

CardReader (SCR) printers.

Grounded

•

Power

When connected to the depot charger, the printer(s) may

AC Power

Jack

Supply

not print.

Cord

Safety Guidelines

•

Do not short the contacts.

•

Use only an Datamax-O'Neil approved power supply.

•

Position the depot charger with enough room to properly

open and close the printer(s); position the depot charger

so it is protected from environmental elements such as

moisture, tools, and boxes; and position the depot

charger in a secure area in normal traffic patterns.

•

Do not operate the depot charger if it appears damaged.

•

To reduce risk of electric shock, unplug the depot charger

before cleaning.

•

Batteries become warm to the touch during charging. If

the battery becomes too hot to touch, discontinue

charging and contact Datamax-O'Neil.

•

Use of any charger or battery not approved by

Datamax-O'Neil for use with their printers

could cause damage to the batteries or printer and will

void the warranty.

•

Datamax-O'Neil does not accept liability for

improperly mounted or poorly placed printers and/or

depot charger.

Mounting the Depot Charger

If the depot charger will be mounted on a vertical

surface or on a wall, use the following procedure to

mount the charging dock:

1. Remove rubber bumpers from the

feet's and AC Adapter cradle.

2. Locate the mounting holes. There are two

mounting holes on either end of the

(Figure 3) and two mounting holes in the middle

of the

(Figure 4).

depot charger

Figure 4

Figure 3

3. Use the

as a template to mark the

depot charger

mounting holes on the mounting surface

(Figure 5). For information on mounting, see the

Guidelines in the previous section.

Figure 5

4. Drill the mounting holes at the marked locations.

Warning: Use caution when drilling the

mounting holes and when mounting the

charger

onto a wall.

5. Attach the

to the mounting surface

depot charger

as follows:

Drywall Surface: Use #8 - #10 toggle bolts (not

included).

Wood Surface: Use #10 x ¼" wood screws.

#10 x ¼" wood screws cannot be used on any

other type of surface.

6. Verify the

is level.

depot charger

7. Thread the screws through the washers,

charger

, and mounting holes and tighten securely.

8. Proceed to Attaching the Power Supply.

depot charger

depot