DutchWest 16 Інструкція з монтажу - Сторінка 4
Переглянути онлайн або завантажити pdf Інструкція з монтажу для Аксесуари DutchWest 16. DutchWest 16 4 сторінки. Inner top replacement kit for the dutchwest extra large convection heaters
Друкувати сторінку9. Turn the damper crank to its highest position and
install the damper, secure it at each end with a steel
tab held in place with a hex head bolt. (Fig. 3)
10. Join the damper adjuster to the damper with a hex
head bolt and a nut. The bolt passes through the for-
ward hole in the base of the adjuster; the nut attach-
es to the bolt on the underside of the damper. Open
the damper or reach through the firebox to reach
the nut. Use the damper handle to test the damper
for smooth operation and adjust as needed; the
rearward bolt in the base of the adjuster regulates
the pressure on the damper. Loosen the forward
(anchor) bolt on the damper. Turn the adjusting bolt
clockwise to tighten the damper. However, do not
overtighten; the metal parts will expand under heat.
The damper should be snug, but not tight, when
the stove is cold. Use a piece of paper between
the damper and its gasket to gauge how tight the
damper is. When the damper is adjusted properly,
tighten the anchor bolt and its nut.
11.Put the catalytic combustor in place in the inner top
insert, with a piece of 'Interam' gasket around its bot-
tom edge. (Fig. 7) Put the new refractory insulator in
place over the catalyst; note that its forward bottom
edge is slightly relieved in the center, to accommo-
date the new style insert. The original insulator is not
relieved.
12. Put the decorative brass bar in place in pockets at
the sides of the slot across the top edge of the front
panel.
13. Fasten the outer top into position with bolts and
washers at the corners of the top. The bolts should
be snug, but not tight; overtightening can bow the
top, leading to smoke leakage, and it can also snap
the extensions on the stove sides.
14. Remove any cement which has squeezed out from
any joints onto the outside of the stove. You do not
need to remove squeeze-out on the inside of the
stove.
15. Hand-turn a 1/4" drill bit, through the hole in the
outer top and through the new refractory insulator.
Avoid hitting the catalyst. Replace the probe ther-
mometer, and its chromed sleeve if you took it out.
Do not simply punch the thermometer through the
insulator, this can break off a piece on the underside
of the insulator.
16. On Model 2184 (which has two front doors), make
sure the rocker grates can rotate freely. If they are
jammed, check the position of the loose grate frame
over them. If you need to move this frame, remove
the 'grate back' and the right inner half-wall (if so
4
equipped). Each of these panels mounts with two
hex head bolts. You will probably need penetrating
oil to loosen these bolts. With these two panels re-
moved, prop the rear edge of the grate frame up out
of the way so you can properly position the rocker
grates. Be careful with your hands when you lower
the grate frame into position over the rocker grates.
Replace the grate back and right inner half-wall.
17. Replace the front door(s) and the side door; simply
slide their hinge pins into place on stubs on the front
and side panels. Do not strike them sharply with
any object. You may need to wiggle the doors back
and forth while pressing downward to seat the doors
properly.
18. Let the cement dry for at least 24 hours. When you
fire up the stove, treat it as a new one because of
the new cast iron parts; 'cure' it with four to six small
fires before you resume regular burning. Each fire
should be about 100° hotter and an hour longer than
the previous one. Use a surface thermometer on the
side door as your guide to firebox temperatures. The
probe thermometer in the stove top registers catalyst
temperatures, which are much higher than firebox
temperatures.
19. Discard the original inner top, baffle and refractory
insulator.
'Interam Gasket'
Inner Top
Channel
Cap
Inner Top Insert
Fig. 7 Inner top and associated parts.
MHSC
149 Cleveland Drive • Paris, Kentucky 40361
www.mhsc.com
Top
Refractory
Insulator
Catalyst
Air Distributor
'Interam Gasket'
ST796
inner top parts
5/04
Inner Top
ST796