Datasensor S65-PA-5-Z Інструкція з експлуатації - Сторінка 3

Переглянути онлайн або завантажити pdf Інструкція з експлуатації для Аксесуари Datasensor S65-PA-5-Z. Datasensor S65-PA-5-Z 3 сторінки. Line sensor

Друкувати сторінку

OUT

Dig1

This operation is necessary when objects, inside the operating area, must not be detected.

- Detection of the reflecting tape characteristics

- Press contemporily the + and – push-buttons for at least 6s.

- The "TAPE" message appears.

OUT

Dig1

- The reflecting tape characteristics are memorised when the push-buttons are released (the

"TAPE" message blinks for 2s, 4Hz) and the sensor returns to the normal mode.

OUT

Dig1

This operation is particularly suggested in the "AREA" operating mode as this mode is very sensitive

to the reflecting tape characteristics.

REMOTE FUNCTIONS

KEYLOCK

The keyboard block function is activated at powering on, connecting the SYNC terminal to the

positive power supply (+Vdc) for at least 1 s, and the push-buttons are NO LONGER active.

After the first second, the SYNC input is ready for the normal functioning and if the SYNC is passive

the outputs are deactivated.

To deactivate the keyboard block, the sensor has to be turned off and re-powered maintaining the

SYNC wire not connected or ground connected (GND).

SYNC input

The SYNC signal allows to determine precisely the beginning and end of the identification.

The identification cycle begins after the transition of the SYNC signal from passive to active and the

sensor outputs are updated after max. 8 ms.

All the outputs are deactivated after max. 8 ms from the active – passive transition.

The connection of the SYNC wire to +Vdc corresponds to the passive logic status while SYNC not

connected or connected to 0 V corresponds to the active.

RS485 serial connection (only for S65-PA-5-Z09-xxxZ versions)

The complete sensor remote control is obtained using a RS485 line.

All the functions, such as the threshold selection and functioning modes, can be accessed through

the serial line.

The serial communication parameters are: 9600 baud, non-parity, 8 data bits, 1 stop bit.

All the commands have to be sent via terminal in an ASCII format according to the folllowing

instructions.

- Reading of the sensor status:

At any moment, at the receipt of the 'r <CR> <LF>' command, the sensor configuration is returned.

- Reading of the measurement::

At any moment, at the receipt of the 'v <CR> <LF>' command, the value of the measurement made

by the sensor is returned, in the 'xxxx<CR> <LF>' format (the xxxx are four ASCII characters).

- Remote detection of the thresholds:

To access into the remote detection mode, the SYNC input has to remain passive for at least 300

ms. The commands available are:

@ <CR> <LF>

beginning of the remote setting mode (together with SYNC passive)

threshold selection, with x ∈ {1,2}

cx <CR> <LF>

txxxx <CR> <LF>

threshold value selection, with xxxx ∈ {0..1023}

e <CR> <LF>

memorisation of the configuration sequence.

q <CR> <LF>

exit from the remote setting without saving the configuration.

If the SYNC input is activated before the 'e' (execute) command is given, the sensor exits the

remote setting mode without saving the configuration, similarly to the receipt of the 'q' (quit)

command.

If the SYNC input is active, at the receipt of the @ <CR> <LF> command, the sensor responds

with: ?? <CR> <LF>. At the receipt of the q <CR> <LF> or e <CR> <LF> commands, the sensor

transmits ok <CR> <LF>.

- Remote detection of the operating area:

To access into the remote detection mode, the SYNC input has to remain passive for at least 300

ms. The commands available are:

@ <CR> <LF>

beginning of the remote setting mode (together with SYNC passive)

w <CR> <LF>

acquisition command of the operating area

e <CR> <LF>

memorisation of the configuration sequence.

q <CR> <LF>

exit from the remote setting without saving the configuration.

If the SYNC input is activated before the 'e' (execute) command is given, the sensor exits the

remote setting mode without saving the configuration, similarly to the receipt of the 'q' (quit)

command.

If the SYNC input is active, at the receipt of the @ <CR> <LF> command, the sensor responds

with: ?? <CR> <LF>. At the receipt of the q <CR> <LF> or e <CR> <LF> commands, the sensor

transmits ok <CR> <LF>.

- Remote detection of the reflecting tape characteristics:

To access into the remote detection mode, the SYNC input has to remain passive for at least 300

ms. The commands available are:

@ <CR> <LF>

beginning of the remote setting mode (together with SYNC passive)

u <CR> <LF>

detection command of the reflecting tape characteristics

Dig2

Dig3

Dig4

SET

Dig2

Dig3

Dig4

SET

Dig2

Dig3

Dig4

SET

e <CR> <LF>

q <CR> <LF>

If the SYNC input is activated before the 'e' (execute) command is given, the sensor exits the

remote setting mode without saving the configuration, similarly to the receipt of the 'q' (quit)

command.

If the SYNC input is active, at the receipt of the @ <CR> <LF> command, the sensor responds

with: ?? <CR> <LF>. At the receipt of the q <CR> <LF> or e <CR> <LF> commands, the sensor

transmits ok <CR> <LF>.

- Reset of the sensor default configuration:

To access into the remote detection mode, the SYNC input has to remain passive for at least 300

ms. The commands available are:

@ <CR> <LF>

z <CR> <LF>

e <CR> <LF>

q <CR> <LF>

If the SYNC input is activated before the 'e' (execute) command is given, the sensor exits the

remote setting mode without saving the configuration, similarly to the receipt of the 'q' (quit)

command.

If the SYNC input is active, at the receipt of the @ <CR> <LF> command, the sensor responds

with: ?? <CR> <LF>. At the receipt of the q <CR> <LF> or e <CR> <LF> commands, the sensor

transmits ok <CR> <LF>.

- Operating mode configuration:

To configure the operating mode, the SYNC input has to remain passive for at least 300 ms. The

commands available are:

@ <CR> <LF>

mx <CR> <LF>

e <CR> <LF>

q <CR> <LF>

If the SYNC input is activated before the 'e' (execute) command is given, the sensor exits the

remote setting mode without saving the configuration, similarly to the receipt of the 'q' (quit)

command.

If the SYNC input is active, at the receipt of the @ <CR> <LF> command, the sensor responds

with: ?? <CR> <LF>. At the receipt of the q <CR> <LF> or e <CR> <LF> commands, the sensor

transmits ok <CR> <LF>.

- Delay configuration:

To configure the delay, the SYNC input has to remain passive for at least 300 ms. The commands

available are:

@ <CR> <LF>

dx <CR> <LF>

e <CR> <LF>

q <CR> <LF>

If the SYNC input is activated before the 'e' (execute) command is given, the sensor exits the

remote setting mode without saving the configuration, similarly to the receipt of the 'q' (quit)

command.

If the SYNC input is active, at the receipt of the @ <CR> <LF> command, the sensor responds

with: ?? <CR> <LF>. At the receipt of the q <CR> <LF> or e <CR> <LF> commands, the sensor

transmits ok <CR> <LF>.

NOTE: the single characters have to be distanced amongst themselves at least 1 ms, during

the command transmission.

DECLARATION OF CONFORMITY

We DATASENSOR S.p.A. declare under our sole responsibility that these products are conform to

the 89/336 CEE, 73/23 CEE Directives and successive amendments.

WARRANTY

DATASENSOR S.p.A. warrants its products to be free from defects.

DATASENSOR S.p.A. will repair or replace, free of charge, any product found to be defective during

the warranty period of 36 months from the manufacturing date.

This warranty does not cover damage or liability deriving from the improper application of

DATASENSOR products.

DATASENSOR S.p.A. Via Lavino 265

40050 Monte S. Pietro - Bologna - Italy

Tel: +39 051 6765611

http://www.datasensor.com

DATASENSOR S.p.A. cares for the environment: 100% recycled paper.

DATASENSOR S.p.A. reserves the right to make modifications and improvements without

prior notification.

memorisation of the configuration sequence.

exit from the remote setting without saving the configuration.

beginning of the remote setting mode (together with SYNC passive)

default sensor configuration reset command

memorisation of the configuration sequence.

exit from the remote setting without saving the configuration.

beginning of the remote setting mode (together with SYNC passive)

operating mode selection, with x ∈ {0, 1, 2, 3, 4}

m0 = end object position

m3 = width measurement

m1 = beg object position

m4 = area measurement

m2 = centre position

memorisation of the configuration sequence.

exit from the remote setting without saving the configuration.

beginning of the remote setting mode (together with SYNC passive)

delay selection, with x ∈ {0,1,2,3,4,5}

d0 = 0 ms

d3 = 20 ms

d1 = 5 ms

d4 = 30 ms

d2 = 10 ms

d5 = 40 ms

memorisation of the configuration sequence.

exit from the remote setting without saving the configuration.

DETECTION DIAGRAMS

Fax: +39 051 6759324

e-mail: [email protected]

826002010 Rev.00