AUSRANVIK APR-50B Посібник користувача та технічні характеристики продукту - Сторінка 5

Переглянути онлайн або завантажити pdf Посібник користувача та технічні характеристики продукту для Холодильник AUSRANVIK APR-50B. AUSRANVIK APR-50B 8 сторінок.

Друкувати сторінку

3.3.7 Long press SET button for 6 seconds, the display will start flashing E1 code, when E1

keeps flashing you press SET button again the code will switch from E1, E2, E3, E4, E5, F1,

F2, F3 and F4. When staying in a specific code you can press UP or DOWN button to

change the parameter according to your need. Every codes represents something you can

calibrate by yourself, and here below is what it means by each code:

Code

Setting

To calibrate the

temperature

lower range

To calibrate the

temperature

upper range

Compressor OFF

Temperature

Compressor

KICKS IN

temperature

Compressor

retardation time

Temperature

Display Calibrate

(for 0 ~ -6°C)

Temperature

Display Calibrate

(for -6 ~ -12°C)

Temperature

display Calibrate

(for below -12°C)

Celsius to

Fahrenheit

(Note: F4 is after F3 code, but it will not display F4 wording, instead the digit number keeps

flashing).

3.3.8 How to resume to factory default setting: In E1 code (see 3.3.7), press UP and DOWN

button at the same time for 6 seconds, the digit number will read 888, 6 seconds later it will

resume to the factory default setting.

Default

Range

Value

-20°C

-40°C

10°C

40°C

1°C

1~10°C

1°C

1~10°C

1~10

3 minutes

minutes

0°

-5 ~ 5°C

0°

-5 ~ 5°C

0°

-5 ~ 5°C

°C

Details

The default lowest temperature you can set is -20°C,

maximum you can set it to be -40°C, which means after

you reset this value, you can select your desire

temperature lower than -20°C (lowest -40°C), the

compressor will not stop running until the interior

temperature goes to -40°C.

Same principle as E1

In default value 1°C, assuming you set the temperature to

be 5°C, when the temperature gets to 4°C (1°C lower

than 5°C), the compressor will shut off automatically; if

you change the value to be 2°C, the compressor will shut

off when temperature gets to 3°C (2°C lower than 5°C)

In default value 1°C, assuming you set the temperature to

be 5°C, when the interior temperature rise up to 6°C (1°C

higher than 5°C), the compressor will resume to run; if

you change the value to be 2°C, the compressor will

resume to work when the interior temperature rise up to

7°C (2°C higher than 5°C).

In default value, if you plug the refrigerator to the electric

power source, the compressor will wait 3 minutes before

running. You can change the time from 1 to 10 minutes

according to your need.

If you find the displaying temperature does not match the

real temperature, you can calibrate the temperature

display within the range. For example if the real

temperature is 2°C but it displays 0°C, you can change

the parameter to be 2°C, then the display will read 2°C

instead of 0°C.

Same as F1. Between -6 ~ -12°C, for example, the real

temperature is -6°C but it displays -8°C, you can change

the parameter to be 2°C, then the display will read -6°C

instead of -8°C.

Same as F1. For temperature below -12°C, for example if

the real temperature is -14°C but it displays -16°C, you

can change the parameter to be 2°C, then the display will

read -14°C instead of -16°C.

Switch between °C and °F.