Fright Ideas EscapeKeeper Посібник із швидкого старту - Сторінка 2

Переглянути онлайн або завантажити pdf Посібник із швидкого старту для Контролер Fright Ideas EscapeKeeper. Fright Ideas EscapeKeeper 2 сторінки.

Друкувати сторінку
Output Wiring
12 VDC MAGLOCK
E-STOP N.C.
STOP
CONTACT
NOTE: OUTPUT 1
MODE MUST BE
2 OR 4 FOR E-STOP
DETECTION.
-
-
-
+
+
+
1
2
3
12 VDC 1.5A EA
OUTPUTS
MAGLOCK WITH E-STOP DETECTION
OUTPUTS CAN BE USED
TO CONTROL ANY 12 VDC
DEVICES UNDER 1.5
AMPS (18 WATTS).
SOLENOID
LED LIGHT
PASS
FAIL
INDICATOR LIGHTS
BEACON
-
+
-
+
-
+
1
2
3
12 VDC 1.5A EA
OUTPUTS
ANY 12 VDC DEVICE
Initial Setup and Factory Reset
Power up holding button 3 to enter setup mode. You can let go when the MODE light starts flashing blue. The
current setting will be shown on the yellow LEDs. For each step below, use the volume knob to adjust the setting,
then tap 3 to advance to the next step. You must advance through all the settings for any changes to be saved.
NOTE: If you get stuck you can visit help.frightideas.com/504 to see a video of the setup process.
Initial Setup Steps
Puzzle Mode
The puzzle mode defines how the EscapeKeeper operates.
Input Sequence - Players must activate the inputs in a specific sequence.
1 2 3 4 5 6 7 8
Morse Code - Players must match your sequence of short and long presses.
1 2 3 4 5 6 7 8
x1
Input State Match - Players must match the inputs to a recorded input state.
1 2 3 4 5 6 7 8
Number of Inputs - Players must activate a certain number of inputs.
1 2 3 4 5 6 7 8
Mission Impossible - Players must activate win input without tripping others.
1 2 3 4 5 6 7 8
Number of Puzzle Inputs
Number of buttons, switches, or sensors used for the puzzle. Remaining inputs can play sounds or hints.
Puzzle Inputs - Select the number of inputs used in the puzzle. For Mission
x2
1 2 3 4 5 6 7 8
Impossible mode see the full manual online for more information.
Output 1 Mode
Output 1 is dedicated to lock control or success indication. Choose one of the modes below.
Maglock, NO E-Stop, Unlock - Maglock, unlocks on failure / timeout.
1 2 3 4 5 6 7 8
Maglock, E-Stop, Unlock - E-Stop detection on, unlock on failure / timeout.
1 2 3 4 5 6 7 8
Maglock, NO E-Stop - Maglock
1 2 3 4 5 6 7 8
x3
Maglock, E-Stop - Maglock, E-Stop detection.
1 2 3 4 5 6 7 8
Pulse On - Output will turn on for 1 second if the puzzle is solved.
1 2 3 4 5 6 7 8
Turn On - Output will turn on and stay on if the puzzle is solved.
1 2 3 4 5 6 7 8
Link Mode - Use to link this unit to one that will turn on after this one is solved.
1 2 3 4 5 6 7 8
12 VDC MAGLOCK
LATCH
NOTE: OUTPUT 1 MODE
NOTE: OUTPUT 1
MUST BE 1 OR 3.
MODE MUST BE 5 TO
PULSE THE LATCH
ON SUCCESS.
OR
-
-
-
+
+
+
1
2
3
12 VDC 1.5A EA
OUTPUTS
MAGLOCK OR SOLENOID LATCH
TAKE APPROPRIATE
TO WALL
!
SAFETY PRECAUTIONS
OUTLET
WHEN WIRING HIGH
VOLTAGES.
12 VDC
RELAY
COIL RELAY
-
-
+
-
+
-
+
1
2
3
12 VDC 1.5A EA
OUTPUTS
ANY 110 VOLT LOAD
Initial Setup Steps (continued)
Auto-Reset Timer
This timer starts when the puzzle is solved or fails due to timeout or too many attempts. When it expires
it restarts the puzzle allowing it to be solved again.
Off
1 2 3 4 5 6 7 8
x4
After Sound
1 2 3 4 5 6 7 8
5 sec
1 2 3 4 5 6 7 8
15 sec
1 2 3 4 5 6 7 8
Game Timer
Used to automatically fail the game if the players take too long.
Off
1 2 3 4 5 6 7 8
1 min
1 2 3 4 5 6 7 8
x5
2 min
1 2 3 4 5 6 7 8
3 min
1 2 3 4 5 6 7 8
Puzzle Mode Options
!
If the MODE light starts blinking green, select ONLY 1 of the tables below based on the Puzzle
Mode you selected in the first step. Once the MODE light turns off your setup is complete.
ONLY FOR
Input Sequence & Morse Code Puzzle Modes
Miss on Input Timeout
Use this to limit the maximum number of seconds between inputs in the sequence. This option will fail
x1
the current attempt and play any Miss sound if they take too long to activate the next input, button, etc.
No Timeout - There's no limit to how long they can take.
1 2 3 4 5 6 7 8
Timeout - Number of seconds until the current attempt times out. (6 shown)
1 2 3 4 5 6 7 8
Options
Move the flashing cursor using the knob. Toggle options off and on by tapping REC. .
Once your options are set, tap button 3 to complete the setup process.
Miss at Code Length - The attempt will miss when the number of input entries
x2
1 2 3 4 5 6 7 8
(usually button presses) in their attempt matches the amount in your solution.
This will tip them off to the length of the code if you have a Miss sound.
Miss on Bad Input - The current attempt will be declared a miss as soon as
1 2 3 4 5 6 7 8
they trigger the wrong input. If you have a Miss sound, this would allow the
players to slowly figure out the code by trial and error. (ignored for Morse Code)
Note: More options described in the Operating Manual online
ONLY FOR
Input State Match Puzzle Mode
Options
Move the flashing cursor using the knob. Toggle options off and on by tapping REC. .
Once your options are set, tap button 3 to complete the setup process.
x1
Use Submit Button - Instead of having the puzzle succeed once they've
1 2 3 4 5 6 7 8
matched the input state, require them to also press a button. This submission
allows you to limit the number of tries they have, for example, to disarm a bomb,
launch a missle, etc. Connect button to input 8, or 7 if puzzle bypass is enabled.
x2
Minimum Match Time - See Operating Manual online or leave at 3.
ONLY FOR
Number of Inputs Puzzle Mode
Latched Inputs
Move the flashing cursor using the knob. Toggle inputs to latched mode by tapping REC.
x1
Once your inputs are set, tap button 3 to complete the setup process.
If you are using buttons or momentary outputs that do not keep the input on until
1 2 3 4 5 6 7 8
the puzzle is finished then you need to enable latch mode for those inputs.
Advanced Options
See the Advanced Options section in the full manual if you'd like write-protection, a puzzle bypass, a limit on the
number of attempts, or an RFID chatter filter.
Factory Reset
Power up holding the black 2 & 3 buttons. Let go when the REC LED flashes red continuously. Sounds will NOT
be erased.
30 sec
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 min
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
2 min
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
5 min
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
4 min
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
5 min
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
10 min
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
15 min
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
REC
REC
REC
10 min
15 min
30 min
60 min
20 min
30 min
40 min
50 min
60 min
ON/OFF
ON/OFF
ON/OFF