DVS EC RECLAIM CONNECT Посібник користувача - Сторінка 4

Переглянути онлайн або завантажити pdf Посібник користувача для Домашня автоматизація DVS EC RECLAIM CONNECT. DVS EC RECLAIM CONNECT 6 сторінок.

Друкувати сторінку

Humidity settings

For adjusting the sensitivity of the system to an air supply

which is more humid than the air inside the home. A higher

setting will mean the system reacts more quickly to a humid

air supply then remains off for a period of time and until

the air supply is dry enough to continue ventilating your

home. The DVS® technician sets this function when the

system is installed, however, this setting can be increased or

decreased.

Note: To prevent nuisance stopping and starting

(oversensitivity) the DVS® is programmed to allow some

minor higher air supply humidity readings before it will stop

ventilating. Please call DVS® on 0800 387 387 if you need

assistance and before you adjust these settings.

Humidity settings

Touch settings icon

then –

SETTINGS > HUMIDITY

– Scroll the Humidity sensitivity or Humidity time

CONTROL

up or down to the level you wish -

Sensing & control

For enabling or disabling the CO

technician enables this function and pairs the sensor(s)

when the system is installed, however, this function can be

Enabled (turned on) or Disabled (Turned off).

Enable / Disable

Touch settings icon

then –

SETTINGS > CO

(touch the Enable/Disable slide switch icon to

> ENABLE

change to Enable or Disable) -

Sensors

The DVS® Connect range has one remote plug in CO

as a standard inclusion. Extra sensors can be fitted with a

maximum of four sensors per system. When multiple sensors

are fitted the system uses the average CO

all sensors to activate a higher ventilation rate when the

average CO

concentration rises above 1000ppm.

Connecting CO

sensors to the system

Plug in the CO

sensor in your room of choice (typically a

living room or master bedroom, however any room which

is normally occupied and has a DVS® vent in it will be

fine). Press and hold the pairing button on the front of the

sensor until the green LED light, (this is only visible when

looking through the vent at the bottom of the sensor) is on

continuously. This takes 5 seconds. If the LED light is a little

difficult to see, just hold the button in and count 7 seconds.

For further assistance please call DVS

OK > EXIT

control function. The DVS®

CONTROL

OK > EXIT

sensor

reading across

This puts the CO

sensor in pairing mode, which lasts 60

seconds.

Then go to the DVS® controller:

Touch the settings icon

UTILITIES > MANAGE CO2 > ADD SENSOR

A box will show, which initially just says Connecting

When the CO

sensor has been found the box shows

Success, New CO2 Sensor added

Repeat for additional sensors (up to 4 can be

connected).

Once the sensor(s) has been added, press

preparation for connection is now made.

Note: After Restarting, the system will need approximately

20 minutes to establish proper connections and begin

accurate CO

level readings. A CO

appear on the home screen and detailed information will be

available in the diagnostics menu.

If you have more than one sensor, each will need to be

individually paired to the controller rather than pairing them

all at the same time. Select

RESTART

WiFi connection and software upgrades

To check for upgrades or reconnect to your WiFi

Touch the WiFi icon

then choose – WiFi Scan or Check

for upgrades (whichever is applicable) – then follow the

instructions.

Clock

To manually adjust the clock

11:20

Touch the clock numbers

EXIT

Filter change reminder reset

Touch settings icon

then –

SETTINGS > FILTER OPTIONS >

NEW FILTER INSTALLED > YES > EXIT > EXIT

Note: This setting is intended to reset the filter reminder on

your system. Resetting this means that you will receive a

reminder to change your filter again, on the control panel, in

12 months.

on 0800 387 387

then –

. The

RESTART

level indicator will

when all are connected.

then -

SET DATE AND TIME >