BENDIX ST-3 Посібник із швидкого старту - Сторінка 3

Переглянути онлайн або завантажити pdf Посібник із швидкого старту для Блок управління BENDIX ST-3. BENDIX ST-3 4 сторінки. Safety valve
Також для BENDIX ST-3: Посібник (4 сторінок)

Друкувати сторінку

ADJUSTMENT OF SAFETY VALVE

NOTE: The Bendix

ST‑3

The pressure setting of the safety valve is stamped on the

cover wrench flat (closest to the pipe thread). The vehicle

manual may also provide the proper pressure setting.

If the setting is not known, determine the governor cut‑

out pressure setting and adjust the safety valve so that

the safety valve closes at a pressure setting somewhat

above governor cut‑out pressure setting (See "Operation"

section).

To adjust, the safety valve must be connected to an air

system with air pressure in excess of desired setting. It

is important that an accurate gauge be used to check

pressure settings while making adjustments.

safety valve is not adjustable.

™

GENERAL SAFETY GUIDELINES

WARNING! PLEASE READ AND

FOLLOW THESE INSTRUCTIONS

TO AVOID PERSONAL INJURY OR DEATH:

When working on or around a vehicle, the following

guidelines should be observed AT ALL TIMES:

▲ Park the vehicle on a level surface, apply the parking

brakes and always block the wheels. Always wear

personal protection equipment.

▲ Stop the engine and remove the ignition key when

working under or around the vehicle. When working

in the engine compartment, the engine should be shut

off and the ignition key should be removed. Where

circumstances require that the engine be in operation,

EXTREME CAUTION should be used to prevent personal

injury resulting from contact with moving, rotating,

leaking, heated or electrically-charged components.

▲ Do not attempt to install, remove, disassemble or

assemble a component until you have read, and

thoroughly understand, the recommended procedures.

Use only the proper tools and observe all precautions

pertaining to use of those tools.

▲ If the work is being performed on the vehicle's air brake

system, or any auxiliary pressurized air systems, make

certain to drain the air pressure from all reservoirs

before beginning ANY work on the vehicle. If the vehicle

is equipped with a Bendix

Bendix

DRM

dryer reservoir module, or a Bendix

™

AD-9si

air dryer, be sure to drain the purge reservoir.

™

▲ Following the vehicle manufacturer's recommended

procedures, deactivate the electrical system in a manner

that safely removes all electrical power from the vehicle.

▲ Never exceed manufacturer's recommended pressures.

▲ Never connect or disconnect a hose or line containing

pressure; it may whip. Never remove a component or

plug unless you are certain all system pressure has

been depleted.

▲ Use only genuine Bendix

components and kits. Replacement hardware, tubing,

hose, ﬁ ttings, etc. must be of equivalent size, type

and strength as original equipment and be designed

speciﬁ cally for such applications and systems.

▲ Components with stripped threads or damaged parts

should be replaced rather than repaired. Do not

attempt repairs requiring machining or welding unless

speciﬁ cally stated and approved by the vehicle and

component manufacturer.

▲ Prior to returning the vehicle to service, make certain all

components and systems are restored to their proper

operating condition.

▲ For vehicles with Automatic Traction Control (ATC),

the ATC function must be disabled (ATC indicator

lamp should be ON) prior to performing any vehicle

maintenance where one or more wheels on a drive axle

are lifted off the ground and moving.

▲ The power MUST be temporarily disconnected

from the radar sensor whenever any tests USING A

DYNAMOMETER are conducted on a Bendix

Advanced

-equipped vehicle.

™

▲ You should consult the vehicle manufacturer's

operating and service manuals, and any related

literature, in conjunction with the Guidelines above.

AD-IS

air dryer system, a

brand replacement parts,

Wingman