Bendix CVS SmarTire TPMS Посібник користувача - Сторінка 3
Переглянути онлайн або завантажити pdf Посібник користувача для Вимірювальні прилади Bendix CVS SmarTire TPMS. Bendix CVS SmarTire TPMS 12 сторінок.
Друкувати сторінку2. OVERVIEW OF THE TOOL FUNCTIONS
Transmitter: The top part of the tool must be pointed
towards the tire to communicate with the sensor. See the
diagram below. For dual-wheel assemblies it is strongly
recommended that the tires are installed with their valve
stems arranged 180° from each other to help make sure
that the transmission reaches the correct sensors.
OUTBOARD
TIRE
LF TOOL
TRANSMITTER
ON/OFF/Mode Select Button: Press and hold this
button for two (2) seconds to power ON the tool. The tool
will sound a beep and the Initiate LED will illuminate to
show that the tool is ON. To toggle the tool
between the sensor Initiate and sensor Learn
functions, press the button briefly. The green
LED for the current mode will be illuminated.
To shut down the tool, press and hold the
button for four (4) seconds. The battery LED
illuminates to show that you can now release the button.
Initiate LED: The Initiate LED will be ON (green) as long
as the Initiate Mode is selected. When pressing the Initiate
button, the LED will blink rapidly for five (5) seconds and
then change to one (1) blink per second after
the initiation has been completed. In service,
the sensor automatically communicates every
3-5 minutes, however the tool prompts an
immediate response.
Learn LED: The Learn LED will be ON (green) as long as
the Learn Mode is selected. Learn transmissions are used
when reprogramming sensor ID codes into the SmarTire
TPMS receiver, either by using the PC-based
Bendix
®
ACom
using the dash-mounted display. When
pressing the Learn button, the LED will blink
rapidly for five (5) seconds and then change
to one (1) blink per second after the Learn transmission
has been completed. Upon being prompted, the sensor
communicates its unique ID code to the receiver.
INBOARD
TIRE
®
Diagnostic software, or by
Initiate/Learn Button: After selecting the initiate or
learn mode, press this button to request the
appropriate response from a sensor. Initiation
transmissions are used to obtain new sensor
readings for the SmarTire gauge or the
diagnostics software.
Low Battery LED: The low battery LED
will flash amber once every second when
the tool is on and the onboard 9-Volt battery
is near empty. Approximately 20 additional
Initiate/Learn operations can be performed after the
battery LED blinks for the first time. The battery LED will
light up solid amber during the shut down process to signal
that the user can release the ON/OFF button.
3. GETTING STARTED
The SmarTire TPMS Low Frequency (LF) tool is powered
by a standard 9-Volt battery. To install the battery, open the
battery access panel on the back of the tool and connect
the supplied battery to the 9-Volt battery connector.
4. USING THE SMARTIRE LF TOOL
Read and understand the General Safety Guidelines
on page two of this document before beginning any
maintenance work on a vehicle.
It is important to make sure that there is no loss of
power to the SmarTire TPMS during the Learn Sensor
procedure. Power interruptions will result in some -
and potentially all - stored sensor location information
being lost, requiring the technician to start over again.
A.
To switch on the SmarTire LF Tool, press and hold
the On/Off/Mode Select button (
seconds.
B.
Enter the Learn (
Mode by toggling the On/Off/Mode
Select switch (
Mode Select button.
®
C.
Hold the tool approximately two (2) in. (5 cm) away
from the tire's surface, at the center of the tire's
sidewall, close to the valve stem. (The recommended
location for all SmarTire TPMS sensors is at the
valve and rim-mounted labels indicate their
location). Do not touch the rim with the tool. Press
and release the Initiate/Learn (
beep will be heard) and hold the tool in place for
five (5) seconds until four (4) quick beeps are heard
to signal that the tool and sensor have communicated
successfully.
3
IMPORTANT
) for two (2)
) or the Initiate (
)
) and then pressing the
) button (a single