2gig Technologies 2GIG-CO1-345 Інструкція з монтажу

Переглянути онлайн або завантажити pdf Інструкція з монтажу для Система безпеки 2gig Technologies 2GIG-CO1-345. 2gig Technologies 2GIG-CO1-345 2 сторінки.

Друкувати сторінку

INSTR,INSTL,2GIG-CO1-345 - P/N: 229921 X4 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 8.500" X 11.000" - SCALE: 1-1 - SIDE 1 of 2

2GIG-CO1-345

WIRELESS

CARBON

MONOXIDE

ALARM

Installation

Instructions

Technical Support

866-670-1591

www.2gig.com

SELECT PROPER LOCATION

Dining

REFER TO SECTION

Kitchen

Room

NUMBER 5 ON THE

Family Room

REAR OF THESE

Living Room

INSTRUCTIONS FOR

IMPORTANT MOUNTING

DETAILS

= Carbon Monoxide

Bedroom

alarm location

FIGURE 1. RECOMMENDED

CO ALARM PLACEMENT FOR

SINGLE FLOOR RESIDENCE

Bedroom

FIGURE 2. RECOMMENDED

CO ALARM PLACEMENT FOR

Kitchen

Living

Garage

MULTI-LEVEL RESIDENCE

Room

= Carbon Monoxide alarm

Basement

location for multi-level

residence

Inside wall location

FIGURE 3. RECOMMENDED

CO ALARM MOUNTING

Height 5' - 6' from floor

LOCATION IS 5 TO 6 FEET

FROM FLOOR

= Carbon Monoxide alarm

mounting location

INSTALL MOUNTING PLATE

SCREW

ANCHORS

FOR WALLBOARD

PLASTIC

SINGLE-GANG

ELECTRICAL BOX

PRINTERS INSTRUCTIONS

PRODUCT DESCRIPTION

The 2GIG-CO1-345 is a carbon monoxide (CO) alarm with a built-in

transmitter designed for use with the 2GIG-CNTRL-345 security system.

The detector gives warning to alert against both the acute and chronic

effects of CO poisoning. When carbon monoxide is detected, the alarm

sounds a loud local alarm. When the local alarm sounds, the built-in

transmitter sends a digitally coded wireless signal to the Control Panel

every 20 seconds until the air has cleared and the detector is restored.

The 2GIG-CO1-345 detector can send four different signals: alarm, test,

low battery, and status.

The local alarm can be silenced once by pressing the TEST/RESET

button. The detector will continue to send an alarm signal every 20

seconds. After 7 minutes, the alarm will sound again if there is still an

unsafe CO concentration level. The reset function can be used only once

for each alarm occurrence.

The Control Panel must be programmed to the detector's serial

number before system testing and operation. Refer to the Control

Panel's instructions for details on programming.

The detector is powered by one 3-volt lithium battery. The battery is

supplied with the detector and can power the unit for more than one year.

If the battery voltage drops below a preset level the alarm will sound a

low battery chirp every 45 seconds and a low battery signal will be sent

to the Control Panel.

When the detector reaches the end of its serviceable life (after about 6

years) a permanent trouble condition will occur and cannot be reset.

Maintenance: Occasionally clean the outside casing with a cloth. Ensure

that the holes on the front of the alarm are not blocked with dirt and dust.

Do not paint, and do not use cleaning agents, bleach, or polish on

the detector.

REMOVE MOUNTING PLATE

Bedroom

TWIST MOUNTING

PLATE TO UNLOCK

Bedroom

PROGRAM CONTROL PANEL

REFER TO CONTROL PANEL'S INSTRUCTIONS

TO PREPARE RECEIVER TO ACCEPT THE

DETECTOR'S SERIAL NUMBER

PRESS UNTIL ALARM

BEEPS THEN RELEASE

TEST BUTTON TO

SEND SIGNAL

DETECTOR

A TEST SIGNAL WILL BE SENT A

FEW SECONDS AFTER THE

SWITCH IS RELEASED

ALARM

SOUNDER

TEST/RESET

BUTTON

NORMAL

OPERATION

ALARM

SIGNAL

TROUBLE

SIGNAL

LOW BATTERY

SIGNAL

END-OF-LIFE

SIGNAL

REMOVE BATTERY TAB

REMOVE

BATTERY TAB

TO APPLY

POWER

REMOVE

MOUNTING

3-VOLT LITHIUM BATTERY - TYPES: DURACELL DL123A,

PLATE

PANASONIC CR123A, SANYO CR123A, ADEMCO 466.

AVAILABLE AT LOCAL RETAILERS AND INTERNET

SUPPLIERS. NOTE: USE ONLY THESE SPECIFIC

BATTERY MODELS.

MOUNT ALARM ON PLATE

TWIST CO ALARM CLOCKWISE TO

LOCK ONTO MOUNTING PLATE

CONTROL PANEL

FEATURES

CARBON

MOUNTING

MONOXIDE

PLATE

ALARM

MOUNTING

SCREWS &

ANCHORS

ALARM SIGNALS

GREEN LED FLASHES EVERY 10 SECONDS.

A REPEATING PATTERN OF FOUR SHORT BEEPS AND

5 SECOND SILENCE. THE RED LED WILL FLASH ONCE

PER SECOND.

DETECTOR SELF-TESTS EVERY 10 SECONDS. IF A

FAULT IS DETECTED, RED LED WILL BLINK EVERY

5 SECONDS AND DETECTOR WILL BEEP EVERY

45 SECONDS. IN THIS CONDITION, THE DETECTOR

REQUIRES IMMEDIATE REPLACEMENT.

RED LED BLINKS EVERY 45 SECONDS.

REPLACE THE BATTERY WHEN THIS SIGNAL OCCURS.

RED LED WILL BLINK ONCE EVERY 10 SECONDS AND

DETECTOR WILL BEEP EVERY 45 SECONDS. IN THIS

CONDITION, THE DETECTOR REQUIRES IMMEDIATE

REPLACEMENT.

NOTE: ON POWER-UP THE RED AND

GREEN LEDS WILL BLINK 4 TIMES,

15 SECONDS APART WHILE

THE ALARM INITIALIZES.

ALIGN TAB IN PLATE WITH

NOTCH IN COVER