Dymo LabelManager 300 Посібник користувача - Сторінка 12
Переглянути онлайн або завантажити pdf Посібник користувача для Виробник етикеток Dymo LabelManager 300. Dymo LabelManager 300 13 сторінок.
Друкувати сторінку
EURO SET-UP
To set the currency for conversion to Euros:
• Press
+
will show the previously selected currency and its
conversion rate into Euros, eg:
BEF
BF40,3399
• Use
or
to step through the currencies available:
Austria: 13,7603 öS
Belgium: BF 40,3399
Germany: DM 1,95583
Spain: 166,386 Pts
Finland: 5,94573 mk
France: 6,55957 Fr
Ireland: £ 0.78756
Italy: L1936,27
Luxembourg: LF 40,3399
e1 = _
Press
to confirm the selection.
• The next time that you press
conversion will be between Euros and the chosen
currency.
The line showing e1 = _ is user-definable. You can enter a
currency symbol and rate for your currency against the
Euro, eg $US. Note that for currencies larger than the
Euro, you must enter '0' before the decimal point of the
value.
Symbols and special characters
INTERNATIONAL CHARACTERS
To add a diacritical (accent) to create an international
character, enter the character first, followed immediately
by the diacritical, e.g. press
get é.
To add a diacritical to an existing character, use
to place the cursor under the character to the right of the
character to be changed, then press the appropriate
diacritical key.
SYMBOLS
SYMBOLS
+
• Press to show symbols and special characters, some of
which are not available direct from the keyboard. The
display will show the last used symbol character, for
A1
example:
it. Each letter selects a line of symbol characters,
numbered 1 to 6, as shown in the table on page 2.
• Press
to cancel, or
DEL
• Press a letter key 'A' to 'Z' until you find the line of
symbols required. You can then press a number key '1'
to '6' to select the symbol required.
Alternatively, use
to Z, then use
or
symbol required.
Press
to place the symbol in the label.
and then
. The display
C
or
+
C
followed by
to
E
/
with a line of symbols above
or
to step through the rows A
to move the cursor under the
PRINT CONTRAST — may be adjusted by pressing
contrast symbols
• Use
• Press
revert to the mid-setting when the LabelManager is
turned off and on again.
Note: This function enables you to adjust the print
quality under extreme temperature conditions.
Cleaning
• Clean the cutter blade regularly: Press and hold down
cutter lever E to expose cutter blade F
cotton bud and alcohol to clean both sides of the blade.
Release cutter lever E.
• Check and clean print head face F
cotton bud and alcohol ONLY.
Troubleshooting
C
, the
C
No display
• check machine is on
• replace discharged batteries
• check AC adaptor.
No printing or poor text
• replace discharged batteries
• check tape cassette installed correctly
• clean the print head
• replace the tape cassette.
Poor print quality with white ink
• When using a White on Black or a White on Clear
cassette, it may be necessary to use the darkest
contrast setting in order to obtain good print quality.
To change the contrast setting via the keyboard, read
and follow the instructions as described in the
or
paragraph "Print Contrast".
Tape jammed
• lift out tape cassette carefully
• remove/release jammed tape
• DO NOT cut the ink ribbon – turn spool
• cut off excess label tape
• refit/replace the tape cassette.
Poor cutter performance
• clean the cutter blade regularly
No response to print key
• !!!!!!!!!!!!!!! in the display indicates a printer jam.
Press any key to return to normal display. Open the
cassette compartment and free the jam.
•
indicates discharged batteries. Press any key to return
to normal display. Replace the batteries.
No success?
• Call the DYMO customer service hotline telephone
number in your country – see the warranty booklet.
8
SYMBOLS
+
followed by
or
to select lighter or darker print.
to confirm the setting. The contrast level will
flashing in the display
to display the
PRINT
.
, then use a
regularly using a
C
to tighten