Dymo LabelManager 450D Посібник користувача - Сторінка 13
Переглянути онлайн або завантажити pdf Посібник користувача для Виробник етикеток Dymo LabelManager 450D. Dymo LabelManager 450D 20 сторінок. Dymo labelmanager user's guide
Також для Dymo LabelManager 450D: Посібник користувача (19 сторінок), Посібник користувача (20 сторінок), Огляд (12 сторінок), Швидкий старт (4 сторінок)
Друкувати сторінку
To print multiple copies of the label
1.
Press
.
Settings
2.
Select
Set # Copies and press
3.
Press the up arrow key to increase the number of copies
to print.
4.
Press the down arrow key to begin decreasing the number
of copies from 16.
H
5.
Press
.
6.
Press
to begin printing.
1,2...n
x You may notice a brief pause in printing between each
label for more complex formats.
When printing is finished, the number of copies to print
returns to the default value of 1.
Serializing Your Labels
You can print a series of labels with the last number
incremented by one number. The number of labels serialized
depends upon the number of copies you selected to print. Only
the last series of numbers that follows any letter, space, or
punctuation will be serialized. For example, abc123 will print
as abc123, abc124, abc125; and 123-998 will print as 123-998,
123-999, 123-1000, and so on.
To serialize your labels
1.
Enter the text for your label.
2.
Press
and then select Set # Copies.
Settings
3.
Press the up arrow key to increase the number of
increments to print and press .
4.
Press
+
.
1,2...n
Shift
The labels automatically print, each label incremented by one
number.
Printing a Fixed-Length Label
Normally, the length of the label is determined by the length
of the text entered. However, you may wish to make a label
for a specific purpose that is a fixed length regardless of the
length of the text.
You can specify a fixed length for a label in 2 mm increments
between 40 mm and 400 mm. The preset fixed length is
H
.
100 mm. Any change you make to the fixed-length setting
remains in effect until you change it.
To set the label length
1.
Press
+
.
Shift
2.
Press the up arrow to select
H
press
.
3.
Use the arrow keys to set the length.
H
4.
Press
.
After you print the label, you must reset the fixed-length label
setting to OFF; otherwise, all your subsequent labels will print
with this fixed length.
Adding Barcodes to Labels
The label maker can print barcodes in six standard formats:
UPCA, UPCE, EAN8, EAN13, CODE39, and CODE128.
You can print a barcode on 19 mm and 24 mm label tape; and
you can print only one barcode per label.
The barcode prints horizontally along the label with the text
in small print underneath the barcode. You can optionally
add text before and after the barcode. Or, you can add text
above or below the barcode by creating a two-line label. See
Creating Multi-Line Labels on page 10.
Four of the standard barcodes require a fixed number of
characters to generate the barcode: EAN8, EAN13, UPCA, and
UPCE. CODE39 and CODE128 barcodes allow a variable number
of characters to be entered.
To set the barcode type
1.
Press
.
Settings
2.
Select
Set Barcode and press
3.
Use the arrow keys to select the barcode type and press
One or more question marks appear between the barcode
symbols ( ).
You may see a 0 in the far right position for some barcode
types. This is a check digit and will be replaced with a
number when the barcode data is entered.
4.
Enter the data for the barcode, replacing the question
H
marks, and press
when finished.
Fixed Length On and then
H
.
H
.
13