Dymo LabelPOINT 100 Інструкція з використання Посібник з використання - Сторінка 6
Переглянути онлайн або завантажити pdf Інструкція з використання Посібник з використання для Виробник етикеток Dymo LabelPOINT 100. Dymo LabelPOINT 100 6 сторінок. Electronic labelmaker
Також для Dymo LabelPOINT 100: Інструкція з використання Посібник з використання (18 сторінок), Інструкція з використання Посібник з використання (6 сторінок)
Друкувати сторінку
Print Contrast
+
ı
ı
ı
ı
ı
• The display provides 5 contrast options.
• Use or to select lighter or darker print.
• Press ↵ to confirm the setting. The
contrast level will revert to the mid-setting
when the unit is turned off and on again.
Note: This function enables you to adjust
the print quality under extreme temperature
conditions.
Cleaning
• Clean the cutter blade regularly: Remove
the cassette, then insert the tip of a ball
point pen or pencil between L-shaped
piece D1 and the guide pin – see page 2.
• Press and hold down cutter lever E to
expose cutter blade D3, then use a cotton
ball and alcohol to clean both sides of the
blade. Release cutter lever E.
• Check and clean print head face D4 regular-
ly using a cotton ball and alcohol ONLY.
Changing the cassette
• Open hinged access door as above.(see p.2)
• Hold as shown, then lift cassette B4
straight up and out.
• Ensure tape and ribbon B3 are taut across
mouth of cassette and tape passes between
guideposts before installing as shown. If
necessary, turn spool B5 clockwise to
tighten ribbon.
• Insert cassette and push firmly C3 until it
clicks into place.
When the tape cassette is pushed firmly
into place, the unit automatically adjusts
All manuals and user guides at all-guides.com
the tension of the tape. You will hear a
+
slight noise as the tape is being tightened.
• Ensure tape and ribbon are positioned as
shown between pinch roller C1 and print
head C2.
Troubleshooting
No display
• Check that the machine is on
• Replace discharged batteries
No printing or poor text
• Replace discharged batteries
• Check that the tape cassette is installed
correctly
• Clean the print head
• Replace the tape cassette
Tape jammed
• Lift out tape cassette carefully
• Remove/release jammed tape
• DO NOT cut the ink ribbon – turn spool to
tighten
• Cut off excess label tape
• Refit/replace the tape cassette
Poor cutter performance
• Clean the cutter blade regularly
No response to print key
• !!!!!!!! in the display indicates a printer
jam. Press any key to return to normal
display. Open the cassette compartment
and free the jam.
•
flashing in the display
indicates discharged batteries. Press any
key to return to normal display.
Replace the batteries.
8
No success?
Call the DYMO customer service hotline tele-
phone number in your country – see the war-
ranty booklet.
This product is CE marked in accordance
with EMC directive and the low voltage
directive and is designed to conform with the
following international standards:
• Safety - EN60950, IEC 950, UL 1950
• EMC emissions - EN 55022 Class B, CIS
PR22 Class B, FCC pt 15 Sub pt B Class B
• EMC immunity - EN 50082-1, IEC 801-2
& IEC 801-3
ACCESSORIES
Tape cassettes
Width:
9mm (3/8") 12mm (1/2")
Length:
7m
7m
Black/Clear
40910 45110/45010
Blue/Clear
–––––
45011
Red/Clear
–––––
45012
Black/White
41913 45113/45013
Blue/White
40914
45014
Red/White
40915
45015
Black/Blue
40916
45016
Black/Red
40917
45017
Black/Yellow
40918 45118/45018
Black/Green
40919
45019
White/Clear
–––––
45020
White/Black
–––––
45021
Black/Silver
–––––
45022
Black/Gold
–––––
45023
Black/Fluo Green
–––––
45024
Black/Fluo Pink
–––––
45025
9