Gage Bilt GB752 Інформація про інструмент встановлення - Сторінка 7
Переглянути онлайн або завантажити pdf Інформація про інструмент встановлення для Електроінструмент Gage Bilt GB752. Gage Bilt GB752 13 сторінок.
Також для Gage Bilt GB752: Оригінальна інструкція з експлуатації (20 сторінок), Інформація про інструмент встановлення (12 сторінок)
Друкувати сторінку
FILLING AND BLEEDING TOOL
NOTE:
Air bleeder Assy (704153) is required.
WARNING:
Do not cycle tool without air bleeder assy (704153), or the button head cap screw (402482) and stat-o-seal (S572),
installed in the head cylinder (752119). Severe personal injury may result.
CAUTION:
Before filling handle assy (704132), the air piston assy (704121) should be all the way down.
CAUTION:
When forcing piston rod assy (704138) downward with head cylinder assy (752119) removed, hydraulic oil will eject
forcibly from handle assy (704132).
CAUTION:
Use CAUTION when removing button head cap screws (402482), stat-o-seals (S572) and air bleeder assy (704153). Hydraulic oil
may be under pressure.
WARNING:
Failure to follow these instructions carefully may result in severe personal injury.
To replace a small amount of oil in the tool, attach the air bleeder assy (704153) and connect tool to air line. Cycle ten times. Disconnect air,
remove the air bleeder assy (704153), and reinstall the button head cap screw (402482) and stat-o-seal (S572). on the head cylinder assy
(752119). Torque 35-40 inch lbs. This will ensure the removal of any air from the hydraulic system and its replacement with oil.
* FILLING & BLEEDING VIDEO AVAILABLE AT: www.gagebilt.com/bleeding.wmv
Should it become necessary to completely refill the tool (such as would be required after tool has been dismantled and reassembled),
take the following steps after depressing the actuator lever assy (704343)
1. Remove head cylinder assy (752119) from handle assy (704132). Slowly push piston (752507) completely forward.
2. Fill handle assy (704132) and the oil passage on top of handle assy (704132) with automatic transmission oil, Dexron III or
equivalent. When looking at the top of the handle assy (704132), the oil passage is the hole that is counterbored for o'ring (S832).
3. Replace head cylinder assy (752119) with care, insuring gasket (704129) and o'ring (S832) are properly installed. Apply Loctite
242 to all four button head cap screws (A-928) and torque uniformly to 40 inch lbs. to prevent leakage around gasket (704129).
4. Remove button head cap screw (402482) and stat-o-seal (S572) from head cylinder assy (752119). Install air bleeder assy (704153)
and connect tool to air line, cycle ten times to fully circulate oil through hydraulic system.
5.
DISCONNECT AIR FROM
in the head cylinder assy (752119).
6. Connect air supply. Cycle tool ten times and check stroke of .500 (12.7 mm) (see diagram below). We recommend using a pair of
dial calipers. With the actuator lever assy (704343) released, check dimension (A). With the actuator lever assy (704343)
depressed, check dimension (B). If stroke is not consistent within 1/64" (.0156) repeat bleeding steps 4-6.
TROUBLESHOOTING
Providing all maintenance conditions have been met, follow this systematic approach to diagnosis.
1. MORE THAN ONE PULL IS REQUIRED TO BREAK RIVET.
a)
Tool needs to be bled. (See filling and bleeding instructions.)
b)
Spring has fatigued, replace.
c)
Jaws are stripped or packed with chips. Clean or replace.
2. SLOW OR PARTIAL OPERATION WHEN THE ACTUATOR LEVER ASSY (704343) IS DEPRESSED
a)
Polyseal (A-1134) and o'ring (400791) on the piston (752507) could be worn or damaged. Replace.
b)
Back-up ring (401102) and o'ring (S945) on the piston rod assy (704138) could be worn or damaged. Replace.
c)
Muffler (704146) or filter inside valve spool assy (703142) may be plugged with dirt. Clean thoroughly and back-blow with
compressed air.
d)
Hole in metering screw in valve spool assy (703142) may be blocked or damaged. Hole diameter should be .028". Clear
and size or replace.
3. NO OPERATION WHEN ACTUATOR LEVER ASSY (704343) DEPRESSED
a)
Tool seized due to mechanical failure or damaged parts.
4. OIL LEAKAGE
a)
DO NOT
OPERATE WITH OIL LEAKING FROM TOOL. HIGH PRESSURE OIL MAY CAUSE SEVERE PERSONAL INJURY.
b) Any oil leaking externally should be traced to its source. An o'ring or seal that leaks should be replaced.
5. AIR BYPASS FROM VALVE HOUSING
a)
If the spring (704141) breaks or dislodges, air will flow freely through the muffler (704146). Replace or reset. Valve spring
installation tool (704162) is recommended.
b)
Check o'rings on valve sleeve (703139), valve spool assy (703142), and valve plug (704145). If worn or damaged, replace.
Valve sleeve removal tool (704163) is recommended.
6. FASTENER STEM JAMMED IN NOSE ASSEMBLY
a)
Nose assembly components require service.
disassemble. Replace worn or broken parts. Clean the surface the jaws ride on.
b)
Stems lodged side by side in the follower. Disassemble, remove stems, and reassemble.
c)
Incorrect follower.
S/N: 3210 AND ABOVE
PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
TOOL. Remove air bleeder assy (704153), install button head cap screw (402482) and stat-o-seal (S572)
'A'
.185 (4.7mm)
AND DISCONNECTING THE AIR SUPPLY:
DISCONNECT AIR FROM
TOOL, remove the nose from the tool and
7
'B'
.685 (17.3mm)
REV.11/14