Dyna-Glo RMC-FA150NGDGD Інструкція з експлуатації та посібник із запчастин - Сторінка 4

Переглянути онлайн або завантажити pdf Інструкція з експлуатації та посібник із запчастин для Газовий обігрівач Dyna-Glo RMC-FA150NGDGD. Dyna-Glo RMC-FA150NGDGD 11 сторінок. Natural gas construction heater
Також для Dyna-Glo RMC-FA150NGDGD: Інструкція з експлуатації та посібник із запчастин (10 сторінок)

Друкувати сторінку

Dyna-Glo Delux Operating Instructions and Parts Manual

Dyna-Glo

Construction Heater

local codes, follow the National Fuel Gas

Code Handbook NFPA54/ANSI Z223.1

and the Natural Gas Installation Code,

CAN/CSA B149.1.

Ventilation

A three square foot

WARNING

opening of fresh

outside air must be provided to operate

each heater safely. If the proper air vent

ilation is not provided, carbon monoxide

poisoning can occur. Always be sure that

the proper ventilation is being provided

before starting this heater.

– Do not use this heater for heating

human living quarters.

– Use of direct-fired heaters in the

construction environment can result

in exposure to levels of CO, CO2, and

NO2 considered to be hazardous to

health and potentially life threatening.

– Do not use in unventilated areas

– Know the signs of CO and CO2

poisoning

– Headaches, stinging eyes

– Dizziness, disorientation

– Difficulty breathing, feels of being

suffocated

– Proper ventilation air exchange (OSHA

29 CFR 1926.57) to support combustion

and maintain acceptable air quality

shall be provided in accordance with

OSHA 29 CFR Part 1926.154, ANSI

A10.10 Safety Requirements for

Temporary and Portable Space Heating

Devices and Equipment used in the

Construction Industry or the Natural

Gas and Propane Installation Codes

CSA B149.1

– Periodically monitor levels of CO, CO2

and NO2 existing at the construction

site – at the minimum at the start of

the shift and after 4 hours.

– Provide ventilation air exchange,

For Technical Support or Troubleshooting, Call: 1-877-447-4768, 8:30 am - 4:30 pm CST

Delux Natural Gas

Ventilation (Continued)

either natural or mechanical, as

required to maintain acceptable indoor

air quality.

Installation

WARNING

warnings in the Safety Information

Section on pages 1–3. They are required

to operate this heater safely. Follow all

local and state codes when operating this

heater.

WARNING

after installation or service. Never use an

open flame to check for leaks. Apply a

50/50 mixture of dish soap and water to

each connection. If bubbles appear, there

is a leak. Correct all leaks immediately.

1. Provide the natural gas supply system

(See Natural Gas Supply, on page 3).

2. Connect all plumbing and fittings to

the low-pressure Natural Gas source.

This source must be regulated to a

maximum of 1/2 PSI, and the piping

must be a 3/4'' (19.1 mm) inside

diameter minimum, and not be over

10 feet (3 m) in length.

3. Line up the female threaded end

of the hose with the fitting on the

heater base and tighten.

4. Slowly open valve at natural gas

supply.

5. Check for leaks at all connections.

Figure 3 – Hose and Inlet Connector

NEVER LEAVE THE HEATER

UNATTENDED WHILE BURNING!

Review and under

stand all of the

Be sure to test all

connections for leaks

Hose

Inlet Connector

RMC-FA150NGDGD

After installing all

WARNING

gas piping, and

making the proper connections, be

sure to check for leaks. Apply a 50/50

mixture of dish soap and water to all

connections. Bubbles forming are

evidence of a leak. Be sure to correct

all leaks at once!

6. Close natural gas supply.

Operation

Review and under

WARNING

stand all of the

warnings in the Safety Information

Section on pages 1–3. They are required

to operate this heater safely. Follow all

local and state codes when operating this

heater.

TO START HEATER

1. Follow all safety, installation and

ventilation instructions in this

manual.

2. Position the heater on a stable and

level surface, and be sure that no

drafts blow into the inlet or outlet of

the heater.

3. Plug the power cord of the heater

into a three hole grounded extension

cord. Be sure that the extension cord

is at least 6 feet (1.8 m) long, and is

UL listed.

EXTENSION CORD WIRE SIZE

REQUIREMENTS

• Up to 50 feet (15.2 m) long, use 18

AWG rated cord.

• 51 to 100 feet (15.5 - 30.5 m) long, use

16 AWG rated cord.

• 101 to 200 (30.8 - 61 m) feet long, use

14 AWG rated cord.

4. Following the extension cord

requirements, plug the extension

cord into a 120 volt/60 Hertz, three

hole grounded outlet.

5. Open gas supply valve slowly.