Dynabrade 10172 Посібник із швидкого старту - Сторінка 2

Переглянути онлайн або завантажити pdf Посібник із швидкого старту для Шліфувальна машина Dynabrade 10172. Dynabrade 10172 4 сторінки. Orbital sander

Друкувати сторінку

Central Vacuum / Machine Exhaust

For Model: 10174

57093 Vacuum Adapter

57065 Cone Muffler

Shaded parts Represent 57112 Muffler Assembly.

Important Operating, Maintenance and Safety Instructions

Carefully read all instructions before operating or servicing any Dynabrade® Abrasive Power Tool.

Warning: Hand, wrist and arm injury may result from repetitive work motion and overexposure to vibration.

Important: All Dynabrade air tools must be used with a Filter-Regulator-Lubricator to maintain all warranties.

Operating Instructions:

Warning:

Eye, face and body protection must be worn while operating power tools. Failure to do so may result in serious injury or death. Follow safety

procedures posted in workplace.

1. With power source disconnected from tool, securely fasten abrasive/accessory on tool.

2. Install air fitting into inlet bushing of tool. Important: Secure inlet bushing of tool with a wrench before attempting to install the air fitting to avoid damaging

valve body housing.

3. Connect power source to tool. Be careful not to depress throttle lever in the process.

4. Check tool speed with tachometer. If tool is operating at a higher speed than the RPM marked on the tool or operating improperly, the tool should be

serviced to correct the cause before use.

Maintenance Instructions:

1. Check tool speed regularly with a tachometer. If tool is operating at a higher speed than the RPM marked on the tool, the tool should be serviced to correct

the cause before use.

2. Some silencers on air tools may clog with use. Clean and replace as required.

3. All Dynabrade air motors should be lubricated. Dynabrade recommends one drop of air lube per minute for each 10 SCFM (example : if the tool

specification state 40 SCFM, set the drip rate of your filter-lubricator at 4 drops per minute). Dynabrade Air Lube (P/N 95842: 1pt. 473ml.) is recommended.

4. An air line filter-regulator-lubricator must be used with this air tool to maintain all warranties. Dynabrade recommends the following: 11289 Air Line Filter-

Regulator-Lubricator — Provides accurate air pressure regulation, two-stage filtration of water contaminants and micro-mist lubrication of pneumatic

components. Operates 40 CFM @ 100 PSI has 3/8" NPT female ports.

5. Use only genuine Dynabrade replacement parts. To reorder replacement parts, specify the Model #, Serial #, and RPM of your machine.

6. A motor tine-up kit (P/N 96024) is available which includes assorted parts to help maintain motor in peek operating condition.

7. Mineral spirits are recommended when cleaning the tool and parts. Do not clean tool or parts with any solvents or oils containing acids, esters, keytones,

chlorinated hydrocarbons or nitro carbons.

Safety Instructions:

Products offered by Dynabrade should not be converted or otherwise altered from original design without expressed written consent from

Dynabrade, Inc.

•

Important: User of tool is responsible for following accepted safety codes such as those published by the American National Standards Institute (ANSI).

•

Operate machine for one minute before application to workpiece to determine if machine is working properly and safely before work begins.

•

Always disconnect power supply before changing abrasive/accessory or making machine adjustments.

•

Inspect abrasives/accessories for damage or defects prior to installation on tools.

•

Please refer to Dynabrade's Warning/Safety Operating Instructions Tag (Reorder No. 95903) for more complete safety information.

Model

Length

Number

Inch (mm)

All Models

7-1/4" (184)

Machine Exhaust Assemblies

Self Generated Vacuum (Vac-Ready) / Machine Exhaust

For Models: 10171, 10172, 10173

57065 Cone Muffler

57083 Vacuum Adapter

57066 Muffler Body

56027 Muffler Insert (3)**

56028 Muffler Cap

Height

Machine

Inch (mm)

Weight

4-1/4" (108)

2.75 lbs. (1.2 kg)

Additional specifications: Air Inlet Thread 1/4" (6 mm) NPT • Hose Size 1/4" (6 mm)

57066 Muffler Body

57068 Vac Nozzle

95526 O-Ring

96197 Dowel Pin

Non-Vacuum / Machine Exhaust

57066 Muffler Body

57065 Cone Muffler

** Muffler inserts available in Package of 30 - P/N 56054.

Air Flow Rate

Sound

SCFM (LPM)

Level

13 (368)

83 dBA

(APD97•13)

57067 Vac Tube

For Model: 10170

56027 Muffler Insert (3)**

56028 Muffler Cap

Motor

HP (W)

RPM

.18 (134)

8,000

Air Pressure

PSI (Bars)

90 (6.2)