Dynabrade 56804 Інструкція з експлуатації - Сторінка 4
Переглянути онлайн або завантажити pdf Інструкція з експлуатації для Шліфувальна машина Dynabrade 56804. Dynabrade 56804 8 сторінок. Small grip dynorbital supreme random orbital sander
Друкувати сторінкуBuy parts on line at https://Dynashop.co.uk/ for all things Dynabrade
Motor Assembly/Disassembly Instructions – Dynorbital
Important: Manufacturers warranty is void if tool is disassembled before warranty expires.
A complete Repair Kit, part number 57098, is available which includes special tools for correct disassembly/assembly of tool.
To Disassemble
1. Disconnect tool from power source.
2. Invert machine and secure in vice, using 57092 Collar (supplied in 57098 Repair Kit) or padded jaws.
3. Remove sanding pad with 26 mm open-end wrench (supplied with sander) and shroud or overskirt.
4. Insert 56058 Lock Ring Tool (supplied in 57098 Repair Kit) into corresponding tabs of lock ring and unscrew.
Motor may now be lifted out for service.
Note: To get it started try using 26 mm wrench for leverage or rock the motor back and forth to loosen up the rings.
5. Remove lock ring, washer, front ring and rear ring from motor. Upper motor may now be disassembled. Remove
95626 Snap Ring.
6. Remove the rear plate and the cylinder assembly by securing the cylinder in a bearing separator gripped on the
cylinder exhaust and extra pocket area. Push the motor shaft balancer through the bearing.
7. Remove the rotor, vanes and rotor key from the motor shaft balancer. Remove the front plate using a small
(#2) arbor press. Support the edges of the front plate while pressing on the small end of the motor shaft balancer.
8. a.) If, during step 7, the front plate and 57088 Bearing remain together, press 57088 Bearing out of the front
plate using 57091 Press Tool (supplied in 57098 Repair Kit) as shown in Drawing 1.
b.) If, during step 7, the front plate and 57088 Bearing remains on the motor shaft balancer, it can be removed
with a bearing separator.
9. Remove 01206 Bearing from the rear plate by using a bearing press tool.
10. Disassemble the balancer assembly as follows:
a.) Place motor shaft assembly into a soft jaw vise. Using a thin screwdriver, pick out the end of 95630 Snap Ring
and peel out. This will loosen the balancer assembly.
b.) Screw the threaded portion of the 56056 Bearing Puller (supplied in 57098 Repair Kit) into the 57069 Balancer
Shaft and heat the outside of the motor shaft balancer to approximately 200° F (approximately 10 seconds with a
propane torch). Now, using the slider weight, pull the assembly out.
c.) Press off 56052 Bearing with a bearing separator and remove bearing seal and bearing shield.
11. If during step 10, the 56052 Bearing remains in the motor shaft balancer, it can be removed by the heating the
shaft balancer again and using either an inside bearing puller or a blind hole bearing puller.
To Assemble:
Important: Be certain parts are clean and in good repair before assembling.
1. Assemble the balancer assembly as follows:
a.) Install 95630 Snap Ring onto balancer shaft. Install 95628 Shield with convex face toward hex of balancer shaft.
b.) Install 56053 Seal. Note: Be certain seal is pressed completely over shaft step.
c.) Apply 1 drop of #271 Loctite
56052 Bearing and the outside diameter of the 57069 Balancer Shaft.
d.) Press fit 56052 Bearing with seal side toward hex of balancer shaft up to shaft step as shown in Drawing 2.
This must be a firm press fit for proper retention of bearing.
2. Place the motor shaft balancer in a soft jaw vise with large end-up.
3. Apply 1 drop of #271 Loctite
®
56052 Bearing and slide balancer assembly into the motor shaft balancer until 56052 Bearing is firmly seated at
bottom. Squeeze 95630 Snap Ring into groove in motor shaft balancer to complete the assembly. Remove from vise.
4. Press 57088 Bearing onto the motor shaft balancer down to the shoulder as shown in Drawing 3.
5. Press 57057 Front Bearing Plate onto 57088 Bearing as shown in Drawing 4 and check for smooth rotation.
6. Place the 57090 Rotor and 56047 Rotor Key on the motor shaft balancer. Place the 56073 Vanes into the rotor
slots. Note: Vanes should be lightly lubricated with Dynabrade Air Lube P/N 95842 (or equivalent) before installation.
7. Place 57058 Cylinder Assembly over rotor. The "short" line-up pin goes toward the front plate.
8. Place 57056 Rear Bearing Plate (with 01206 Rear Bearing pressed into place) over shaft and "long" end of line-up
pin and press fit in place as shown in Drawing 5.
9. Place 95626 Snap Ring in groove.
10. Place 57054 Rear Ring over the rear plate and line-up pin. Turn the motor over and place 57055 Front Ring over
the front plate making sure that the "legs and fingers" on the front and rear rings line-up. Also the small cut-outs on
both rings should line-up with the square holes in the cylinder/end plate assembly.
11. Place 95973 Washer and 57059 Lock Ring onto the front ring with 1 drop of pneumatic tool oil spread between the
washer and lock ring.
12. Secure motor housing in vise, using 57092 Collar or padded jaws. Spread 2-3 drops of pneumatic tool oil around the
housing bore for ease of insertion of motor assembly. Slide motor assembly into secured housing.
Note: Be certain line-up pin enters the pocket in the bottom of the housing and the "legs" of the rings stay in line.
13. Tighten lock ring with 56058 Lock Ring Tool to 28 N•m/250 in. - lbs. Attach shroud or overskirt and weight-mated sanding pad.
Tool Assembly Complete. Please allow 30 minutes for adhesives to cure before operating tool.
Buy parts on line at https://Dynashop.co.uk/ for all things Dynabrade
®
(or equivalent) and spread over several places around the inside diameter of the
(or equivalent) and spread over several places around the outside diameter of the
(continued on next page)
4
®
Supreme Sander
Drawing 1
Bearing Press Tool
Front Bearing Plate
Support
57088 Bearing
Drawing 2
Bearing Press Tool
56052 Bearing
Shaft Step
Bearing Seal and
Bearing Shield
Balancer Shaft Assembly
Drawing 3
Bearing Press Tool
57088 Bearing
Motor Shaft Balancer
Balancer Shaft Assembly
57091
57057
57091
57091